Editing Talk:Harddrive

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 15: Line 15:
* When trying to boot to XMB it also errors out with "Harddrive Error 0x8002F281".
* When trying to boot to XMB it also errors out with "Harddrive Error 0x8002F281".
* When replacing the drive for the previous tested 1TB harddrive, it boots without errors to XMB and reports : 827GB free/931GB total
* When replacing the drive for the previous tested 1TB harddrive, it boots without errors to XMB and reports : 827GB free/931GB total
;Conclusion: <span style="color:red!important;">&gt;1TB didn't work.</span>
;Conclusion: <span style="color:red!important;">&gt;1TB didn't not work.</span>


===== Using Factory Service Mode - when trying to install a 1.5TB 3.5" drive as internal (using an eSATA cradle) FSM =====
===== Using Factory Service Mode - when trying to install a 1.5TB 3.5" drive as internal (using an eSATA cradle) FSM =====
Line 35: Line 35:
** Preparing Update counts to 100% and then halts (does not reboot), just like in first trial.
** Preparing Update counts to 100% and then halts (does not reboot), just like in first trial.
* Manual poweroff and reboot just results in blank screen with no harddrive activity
* Manual poweroff and reboot just results in blank screen with no harddrive activity
;Conclusion: <span style="color:red!important;">&gt;1TB didn't work in normal or recovery mode only with FSM enabled.</span>
;Conclusion: <span style="color:red!important;">&gt;1TB didn't not work in normal or recovery mode only with FSM enabled.</span>
===== Going back to the 1TB and crosschecking =====  
===== Going back to the 1TB and crosschecking =====  
* Replacing drive back to the working 1TB (has 3.55 on it) gives prompt to reinstall 2.70, doing so errors out with "Harddrive Error 0x8002F281".
* Replacing drive back to the working 1TB (has 3.55 on it) gives prompt to reinstall 2.70, doing so errors out with "Harddrive Error 0x8002F281".
Line 503: Line 503:
Uses 3.5" (size) hdd's
Uses 3.5" (size) hdd's
*DECR-1000 - 2x Seagate Barracuda ST3400820A6 (7200.10 400Gbytes [email protected] [email protected])
*DECR-1000 - 2x Seagate Barracuda ST3400820A6 (7200.10 400Gbytes [email protected] [email protected])
=Firmware Patches=
==emer_init==
Patch to increase acceptable HDD capacity for error "''The installed hard disk is not supported. You must install a hard disk that is compatible with this system''." Without patch recovery will throw this error when hdd capacity is above 1,649,267,441,664 bytes. With patch error will be shown for hdd above 2,130,303,778,816 bytes. 1,75TB limited drives should be accepted again. Untested on real hardware, use with caution (hw flasher required)! Sorry for short hex pattern, but it should be ok for manual patch (4.75 in this case).
*Search for:
38 00 01 80
Replace to:
38 00 01 F0
For full 2TB replace to (There are likely other factors which will fail):
38 00 02 01
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Template used on this page: