Editing SW2-303

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
<div style="float:right">[[File:Syscon SW2-303.jpg|thumb|Photo of a Syscon 'SW2-303' (QFP Packaging)]]<br>[[File:Syscon SW2-303 Unsoldered.JPG|thumb]]</div>
== SW2-303 (SysCon) ==
*Found in PS3 models:
<div style="float:right">[[File:Syscon SW2-303.jpg|thumb|Photo of a Syscon 'SW2-303' (QFP Packaging)]]<br /><br />[[File:Fp128b_pin_arrangement.png|thumb|QFP Package : 128 pins<br />''pin 1 left bottom at mark, counter clockwise from south (pins 1-38) to east (pins 39-64), north (pins 65-102), west (103-128))'']] <br /> <br />[[File:Syscon SW2-303 Unsoldered.JPG|thumb]]</div>
**[[CECH-25xx]] with motherboard: [[JSD-001]] or [[JTP-001]]
 
*Used on:
**PS3 Slim [[CECH-25xx]] with motherboard: [[JSD-001]] or [[JTP-001]]


*True Name: uPD78F11BB
*True Name: uPD78F11BB
* Uses 3.3v SPI to communicate with the Cell (pins 80-83)
* Uses 3.3v SPI to communicate with the Cell (pins 80-83)


{{Template:Syscon pinout LQFP 128 pins‎}}
=== Pinout ===
{|class="wikitable"
! Pin # !! Name !! Port !! Description !! STBY Voltages
|-
| 1 || P142/SCK20/SCL20  || || Connected to pin27 @Panasonic [[MN8647091]] || 0
|-
| 2 || SB_INT || || SB_INT/SYSCSINT, Connected to pinD1@SB through the resistor. ~1V @ standby (0 V?) || 0
|-
| 3 || BE_INT || || BE_INT/ATTENTION, pinBA17@BE connected through the NPN transistor. 3V @ standby (3.15V) || 3.15
|-
| 4 || || || To +12V_MAIN through the resistor and divider || 0
|-
| 5 || P37/POW_LED || || Connected to dual led(Green) on [[switch boards | switch board]] through the dual digital NPN trans. EMH1(SOT-563) || 0
|-
| 6 || P36/STBY_LED || || Connected to dual led(Red) on [[switch boards | switch board]] through the dual digital NPN trans. EMH1(SOT-563) || 3v @ standby (3.3V)
|-
| 7 || || || Connected to pinAA18@SB || 0
|-
| 8 || || || Connected to pinAA17@SB || 0
|-
| 9 || || || CELL BE related? || 0
|-
| 10 || || || || 0
|-
| 11 || P106 || || Connected to Backlit LEDs on [[switch boards | switch board]] || 0
|-
| 12 || P105 || || Connected to CONTOUR LEDs on [[switch boards | switch board]] || 0
|-
| 13 || P104 || || Absent element between this line and GND. Nothing else.  || 0
|-
| 14 || || || || 0
|-
| 15 || INTP?? || || || 0
|-
| 16 || BUZZER || || || 0
|-
| 17 || P45/SO01  || || || 0
|-
| 18 || P44/SI01  || || 3v @ standby || 3.0
|-
| 19 || P43/SCK01  || || || 0
|-
| 20 || || || || 0
|-
| 21 || TOOL1 || || Connected to Pin 13 @ Service Connector through a missing SMD component resistor/diode || 3.0
|-
| 22 || TOOL0/Debugger Pin? || || Connected to Pin 7 @ Service Connector through a missing SMD component resistor/diode || 0
|-
| 23 || P127/SO21  || || || 0
|-
| 24 || P126/THR_I2C_SDA || || Connected to pin 7 of CELL/RSX [[Thermal | temperature monitor IC's]] (SMbus I2C shared data line) || 3v @ standby (3.15)
|-
| 25 || P125/THR_I2C_SCL || || Connected to pin 8 of CELL/RSX [[Thermal | temperature monitor IC's]] (SMbus I2C shared clock line) || 3v @ standby (3.15)
|-
| 26 || RESET? || || Connected to Pin 9 @ Service Connector through a missing SMD component resistor/diode. And to standby voltage regulator [[Talk:Regulators | 463A]], pin 3 ||
|-
| 27 || P124 || || Connected to the big black external oscilator 1 next to syscon. CLK -> 1-2V Amplitude (32.768Khz?) ||
|-
| 28 || P123 || || Connected to the big black external oscilator 1 next to syscon. CLK -> 1-2V Amplitude (32.768Khz?)  ||
|-
| 29 || P137/FLMD0 || || Connected to pin 8 @ Service Connector through a missing SMD component resistor/diode || 3.33
|-
| 30 || P122 || || Connected to a small external oscilator 2 ? || 0.8v @ standby (1.1)
|-
| 31 || P121 || || Connected to a small external oscilator 2 ? || 2.2v @ standby (2.4)
|-
| 32 || REGC || || ||
|-
| 33 || GROUND/Vss0 || || || 0
|-
| 34 || GROUND/EVss0 || || || 0
|-
| 35 || Vdd || || Connected to voltage regulator [[Talk:Regulators | 463A]], pin 2 (3.3_EVER_B) || 3v @ standby (3.3)
|-
| 36 || EVdd0 || || Connected to voltage regulator [[Talk:Regulators | 463A]], pin 2 (3.3_EVER_B) || 3v @ standby (3.3)
|-
| 37 || P60 || || 0.2v @ standby || 0
|-
| 38 || P61 || || 0.2v @ standby || 0
|-
| 39 || || ||  || 0
|-
| 40 || || || || 0
|-
| 41 || P31/AC IN? || || 3v @ standby (3.3) || 3.3
|-
| 42 || || || Connected (indirectly) to voltage regulator [[Talk:Regulators | BD9684 0906]],  pin 4 || 0
|-
| 43 || P65 || || Connected to Pin 12 @ Service Connector through a missing SMD component resistor/diode  || 3.0
|-
| 44 || || || || 0
|-
| 45 || || || || 0
|-
| 46 || INTP?? || || || 0
|-
| 47 || P76 || || 3v @ standby (3.15) || 3.15
|-
| 48 || P75 || || 3v @ standby (3.15) || 3.15
|-
| 49 || INTP?? || || || 0
|-
| 50 || P73 || || Connected to pin 3 @ Service Connector. And to voltage regulator [[Talk:Regulators | D35653 0S25]] || 0
|-
| 51 || || || || 0
|-
| 52 || || || Connected to voltage regulator [[Talk:Regulators | BD3525]],  pin 12 || 0
|-
| 53 || || || || 0
|-
| 54 || || || || 0
|-
| 55 || || || || 0
|-
| 56 || GROUND/EVss1 || || || 0
|-
| 57 || EVdd1 || || Connected to voltage regulator [[Talk:Regulators | 463A]], pin 2 (3.3_EVER_B) || 3v @ standby (3.3)
|-
| 58 || || || || 0
|-
| 59 || || || || 0
|-
| 60 || || || || 0
|-
| 61 || || || || 0
|-
| 62 || || || || 0
|-
| 63 || || || || 0
|-
| 64 || || || || 0
|-
| 65 || || || || 0
|-
| 66 || INTP?? || || || 0
|-
| 67 || || || || 0
|-
| 68 || || || || 0
|-
| 69 || || || || 0
|-
| 70 || || || || 0
|-
| 71 || || || || 0
|-
| 72 || || || || 0
|-
| 73 || || || || 0
|-
| 74 || || || || 0
|-
| 75 || || || Connected to voltage regulator [[Talk:Regulators | Mitsumi 040 810X]],  pin 5 || 0
|-
| 76 || P16 || || 3v @ standby (3.15) || 3.15
|-
| 77 || P15 || || 3v @ standby (3.3) || 3.3
|-
| 78 || SC_RxD(RxD3/RxD2/P14) || || SC_RxD UART (terminal).Connected to Pin 11 @ Service Connector through a missing SMD component resistor/diode, and to pin 6 @ [[PCI]] Connector || 0
|-
| 79 || SC_TxD(TxD3/TxD2/P13) || || SC_TxD UART (terminal).Connected to Pin 10 @ Service Connector through a missing SMD component resistor/diode, and to pin 4 @ [[PCI]] Connector || 3.3
|-
| 80 || P12/EX26/SO00/TxD0 || || SO from Cell Slave to Syscon Master || 0
|-
| 81 || P11 P11/EX25/SI00/RxD0  || || SI from Syscon Master to Cell Slave || 1.2
|-
| 82 || P10/EX24/SCK00 || || Serial Clock || 0
|-
| 83 || P90 || || Chip Select || 2.0
|-
| 84 || P91 || || 3v @ standby || 3.0
|-
| 85 || || || || 0
|-
| 86 || || || || 0
|-
| 87 || || || || 0
|-
| 88 ||  P95/SCK11/SCL11 || || || 0
|-
| 89 || /SI11/SDA11 || || || 0
|-
| 90 ||  P97/SO11 || || || 0
|-
| 91 || || || || 0
|-
| 92 || || || Connected to voltage regulator [[Talk:Regulators | BD3527 (near FLASH)]],  pin 12 || 0
|-
| 93 || || || || 0
|-
| 94 || || || || 0
|-
| 95 || || || Connected to voltage regulator [[Talk:Regulators | BD3527 (near USB)]],  pin 12 || 0
|-
| 96 || || || || 0
|-
| 97 || P101 || || Connected to voltage regulator [[Talk:Regulators | 463A]], pin 2 (3.3_EVER_B) || 3v @ standby (3.3)
|-
| 98 || || || || 0
|-
| 99 || || || || 0
|-
| 100 || P146 || || Connected to voltage regulator [[Talk:Regulators | 463A]], pin 2 (3.3_EVER_B) || 3v @ standby (3.3)
|-
| 101 || GROUND || || || 0
|-
| 102 || || || || 0
|-
| 103 || || || || 0
|-
| 104 || || || || 0
|-
| 105 || || || || 0
|-
| 106 || || || || 0
|-
| 107 || || || || 0
|-
| 108 || || || || 0
|-
| 109 || P150 || || 3v @ standby  || 3.0
|-
| 110 || P27/POW_SW_DET || || Power switch detect. Connected to [[switch boards | switch board]] || 3v @ standby (3.3) 3.3
|-
| 111 || P26/EJECT_SW_DET || || Eject switch detect. Connected to [[switch boards | switch board]] || 3v @ standby (3.3) 3.3
|-
| 112 || || || || 0
|-
| 113 || || || || 0
|-
| 114 || || || || 0
|-
| 115 || || || || 0
|-
| 116 || || || || 0
|-
| 117 || P20 || || (0V?) || 0
|-
| 118 || P130/ACDC_STBY || || Connected to standby voltage regulator [[Talk:Regulators | 348A]], pins 2 and 7 EN_HDMI ? || 3v @ standby (3.3)
|-
| 119 || P102 || || || 3v @ standby (3.3)
|-
| 120 || || || || 0
|-
| 121 || P04/SCK10/SCL10 || || || 0
|-
| 122 || SI10/RxD1/SDA10 || || || 0
|-
| 123 || P02/SO10/TxD1  || || || 0
|-
| 124 || || || Connected to pin93 @Panasonic [[MN8647091]] || 0
|-
| 125 || || || || 0
|-
| 126 || P145/FAN_PWM || || PWM Control for the Fan. || 0
|-
| 127 ||  P144/SO20/TxD2  || || || 0
|-
| 128 || /SI20/RxD2/SDA20  || || Connected to pin29 @Panasonic [[MN8647091]] || 0
|}
{{Wikify}}
 


{{Motherboard Components}}<noinclude>[[Category:Main]]</noinclude>
{{Motherboard Components}}<noinclude>[[Category:Main]]</noinclude>
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page:

Retrieved from "http://www.psdevwiki.com/ps3/SW2-303"