Editing PCI

<div style="float:right">[[File:PCI pads - as seen on COK-002.jpg|200px|thumb|left|PCI pads - as seen on COK-002<br>note: Two circular pads in the bottom right corner are for southbridge serial]]<br>
[[File:TMU-520_1-871-645-11_A_Detail_9_(CP_Con.).jpg|200px|thumb|left|Communication Processor (PCI) connector beneath the PCIe x4 connector on a TMU-520]]<br>[[File:PCI connector JSD-001 SB and SC UART.jpg|200px|thumb|left|PCI connector JSD-001 SB and SC UART]]</div>

== PCI ==
Bus, resembling Conventional PCI 2.3, directly connected to [[South Bridge]], with 80 exposed pads

Activated by setting offset 0x48C02 in [[SC EEPROM]] to 0x00 or 0x03:
* 0x00 is for IFB (InterFace Board, used by [[SKU_Models_Nonretail#Nonretail_prototypes_.28CEB.29|CEB]])
* 0x03 is for [[Communication Processor]] (PIF5, used by [[SKU_Models_Nonretail#Reference_tool_prototypes_.28DEHR.29|DEH-R10XX]] and [[DECR-1000]])
** Does also have support for '''all''' ''retail platforms'' (e.g. [[COK-00x#COK-001|COK-001]], [[VER-00x#VER-001|VER-001]] or [[RTX-00x#RTX-001|RTX-001]])

Supported devices:
{| class="wikitable sortable"
|-
! Device ID !! Device "Name" !! Firmware
|-
| 104D8183 || Sony IFB ATHENS Board Revision 0x1 || [[010.???]] to {{latest}}
|-
| 104D81FF || Sony PIF5 [[TMR-520|TMR]] Board Revision 0x101 || [[0.6.0.004.r010|060.004]] to {{latest}}
|-
| 104D8200 || Sony DVE (RSX Tracing) FPGA || [[0.8.2.006.r010|082.006]] to {{latest}}
|-
| 104D820E || Sony [[CXD9208GP]] PS2 emulation subsystem adapter || [[0.8.2.006.r010|082.006]] to {{latest}}
|-
| 80861076 || Intel 82541PI Gigabit Ethernet Controller || [[010.???]] to {{latest}}
|-
|}

Major differences from PCI standard:
* smaller formfactor (80 pin, instead of miniPCI 100P-type I/II or MiniPCI 124P-Type III)
* no use of miniPCI standard sideband signals for audio and communications
* no support of the miniPCI standard CLKRUN# signal defined in the PCI Mobile Design Guide
* no support for optional JTAG signals, nor for the 64-bit PCI extension defined in the PCI Local Bus Specification

=== 70/80 pin miniPCI pad layout ===
CN3208 80P on [[CECHAxx]]/[[CECHBxx]] [[COK-00x#COK-001|COK-001]], [[CECHCxx]]/[[CECHExx]] [[COK-00x#COK-002|COK-002(W)]], [[CECH-20xx]] [[DYN-00x#DYN-001|DYN-001]] and '''all''' [[Motherboard_Revisions#DYN-001|later models]]

CN3208 70P on [[CECHGxx]] [[SEM-00x#SEM-001|SEM-001]], [[CECHHxx]] [[DIA-00x#DIA-001|DIA-001]], [[CECHJxx]]/[[CECHKxx]] [[DIA-00x#DIA-002|DIA-002]] and [[CECHLxx]]/[[CECHMxx]]/[[CECHPxx]]/[[CECHQxx]] [[VER-00x#VER-001|VER-001]]

{| class="wikitable sortable"
|-
! 80P<br />Pin !! 70P<br />Pin !! Usage !! 100P<br />Pin<br />(Type I/II) !! 124P<br />Pin<br />(Type III) !! Remark
|-
| 01 || 35 || +3.3V_PCI || 03, 08, 12, 15, 24, 47, 54, 72, 73 || 19, 24, 28, 31, 40, 63, 70, 88, 89 (not 124) || VCC
|-
| 02 || 70 || GND || 7, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 03 || - || PIO15 ||  ||  || ?
|-
| 04 || - || PIO11 ||  ||  || ?
|-
| 05 || - || PIO14 ||  ||  || ?
|-
| 06 || - || PIO10 ||  ||  || ?
|-
| 07 || - || PIO13 ||  ||  || ?
|-
| 08 || - || PIO9 ||  ||  || ?
|-
| 09 || - || PIO12 ||  ||  || ?
|-
| 10 || - || PIO8 ||  ||  || ?
|-
| 11 || 01 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 12 || 36 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 13 || 02 || /INTA || 04 || 20 || Interrupt line A (open-drain)
|-
| 14 || 37 || /INTB || 01 || 17 || Interrupt line B (open-drain)
|-
| 15 || 03 || /INTC || - || - || Interrupt line C (open-drain)
|-
| 16 || 38 || /INTD || - || - || Interrupt line D (open-drain)
|-
| 17 || 04 || /RST || 10 || 26 || Reset
|-
| 18 || 39 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 19 || 05 || /GNT || 14 || 30 || Bus grant from motherboard to card
|-
| 20 || 40 || CLK || 09 || 25 || 
|-
| 21 || 06 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 22 || 41 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 23 || 07 || /PME || 18 || 34 || Power management event. 3.3 V, open drain, active low
|-
| 24 || 42 || /REQ ||  ||  || Bus request from card to motherboard
|-
| 25 || 08 || AD30 || 22 || 38 || Address/Data 30
|-
| 26 || 43 || AD31 || 17 || 33 || Address/Data 31
|-
| 27 || 09 || AD28 || 26 || 42 || Address/Data 28
|-
| 28 || 44 || AD29 || 19 || 35 || Address/Data 29
|-
| 29 || 10 || AD26 || 28 || 44 || Address/Data 26
|-
| 30 || 45 || AD27 || 23 || 39 || Address/Data 27
|-
| 31 || 11 || AD24 || 30 || 46 || Address/Data 24
|-
| 32 || 46 || AD25 || 25 || 41 || Address/Data 25
|-
| 33 || 12 || IDSEL ||  ||  || IDSEL is asserted by PCI system to select the connected device during configuration read and write transactions.
|-
| 34 || 47 || /C/BE3 ||  ||  || Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
| 35 || 13 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 36 || 48 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 37 || 14 || AD22 || 36 || 52 || Address/Data 22
|-
| 38 || 49 || AD23 || 31 || 47 || Address/Data 23
|-
| 39 || 15 || AD20 || 38 || 54 || Address/Data 20
|-
| 40 || 50 || AD21 || 35 || 51 || Address/Data 21
|-
| 41 || 16 || AD18 || 42 || 58 || Address/Data 18
|-
| 42 || 51 || AD19 || 37 || 53 || Address/Data 19
|-
| 43 || 17 || AD16 || 44 || 60 || Address/Data 16
|-
| 44 || 52 || AD17 || 41 || 57 || Address/Data 17
|-
| 45 || 18 || /FRAME || 48 || 64 || FRAME is driven by the current master to indicate the beginning and duration of an access. While FRAME is asserted, data transaction continues. When FRAME is deasserted, the transaction is in the final data phase.
|-
| 46 || 53 || /C/BE2 || 43 || 59 || Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
| 47 || 19 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 48 || 54 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 49 || 20 || /TRDY || 50 || 66 || TRDY indicates the PCI bus slave can complete the current data phase of the transaction.
|-
| 50 || 55 || /IORDY || 45 || 61 || IRDY indicates the PCI bus master can complete the current data phase of the transaction.
|-
| 51 || 21 || /STOP || 52 || 68 || STOP indicates the connected device is requesting that the current master stop the current transaction.
|-
| 52 || 56 || /DEVSEL || 56 || 72 || The connected device drives this signal active to indicate that it has decoded its address as the target of the current access.
|-
| 53 || 22 || PAR || 40 || 56 || The connected device drives PAR in read data phases for parity checking.
|-
| 54 || 57 || /PERR || 55 || 71 || The PERR pin reports data parity errors during data read phases. Even parity over AD[31:00] and C/BE[3:0]#
|-
| 55 || 23 || AD15 || 60 || 76 || Address/Data 15
|-
| 56 || 58 || /SERR || 51 || 67 || System error
|-
| 57 || 24 || AD13 || 62 || 78 || Address/Data 13
|-
| 58 || 59 || /C/BE1 || 57 || 73 || Command/Byte Enable 1 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
| 59 || 25 || AD11 || 64 || 80 || Address/Data 11
|-
| 60 || 60 || AD14 || 59 || 75 || Address/Data 14
|-
| 61 || 26 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 62 || 61 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 63 || 27 || AD09 || 68 || 84 || Address/Data 09
|-
| 64 || 62 || AD12 || 63 || 79 || Address/Data 12
|-
| 65 || 28 || /C/BE0 || 70 || 86 || Command/Byte Enable 0 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
| 66 || 63 || AD10 || 65 || 81 || Address/Data 10
|-
| 67 || 29 || AD06 || 74 || 90 || Address/Data 06
|-
| 68 || 64 || AD08 || 69 || 85 || Address/Data 08
|-
| 69 || 30 || AD04 || 76 || 92 || Address/Data 04
|-
| 70 || 65 || AD07 || 71 || 87 || Address/Data 07
|-
| 71 || 31 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 72 || 66 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 73 || 32 || AD02 || 78 || 94 || Address/Data 02
|-
| 74 || 67 || AD05 || 75 || 91 || Address/Data 05
|-
| 75 || 33 || AD00 || 80 || 96 || Address/Data 00
|-
| 76 || 68 || AD03 || 79 || 95 || Address/Data 03
|-
| 77 || - || SIORXD[0] ||  ||  || Southbridge Serial Receive
|-
| 78 || 69 || AD01 || 83 || 99 || Address/Data 01
|-
| 79 || - || SIOTXD[0] ||  ||  || Southbridge Serial Transceive
|-
| 80 || 34 || /SW_PCI ||  ||  || ?switch PCI?
|-
|}

==== [[South Bridge]] serial ====
{| class="wikitable sortable"
|-
! Pad !! Name !! Usage !! Remark
|-
| JL9385 || +3.3V_SB_VDDIO || VCC || 
|-
| JL9386 || GND || Ground || 
|-
| JL9387 || SB_SIO0-RXD || Receive || 
|-
| JL9388 || SB_SIO0-TXT || Tranceive || 
|-
|}

=== 160 pin pad layout ===
CN4301 160P on [[DECR-1000]] [[TMU-520]] (only partly used for PCI)<br />
'''TODO'''



{{Wikify}}


{{Motherboard Components}}<noinclude>[[Category:Main]]</noinclude>