Editing PCI

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
<div style="float:right">[[File:PCI pads - as seen on COK-002.jpg|200px|thumb|left|PCI pads - as seen on COK-002<br>note: Two circular pads in the bottom right corner are for southbridge serial]]</div>
[[Category:Hardware]]
<div style="float:right">[[File:TMU-520_1-871-645-11_A_Detail_9_(CP_Con.).jpg|200px|thumb|left|Communication Processor (PCI) connector beneath the PCIe x4 connector on a TMU-520]]</div>
<div style="float:right">[[File:PCI pads - as seen on COK-002.jpg|200px|thumb|left|File:PCI pads - as seen on COK-002]]</div>
<div style="float:right">[[File:PCI connector JSD-001 SB and SC UART.jpg|200px|thumb|left|PCI connector JSD-001 SB and SC UART]]</div>


== PCI ==
== PCI ==
Bus, resembling Conventional PCI 2.3, directly connected to [[South Bridge]], with 80 exposed pads
Bus, resembling Conentional PCI 2.3, directly connected to [[South Bridge]], with 80 exposed pads


Activated by setting offset 0x48C02 in [[SC EEPROM]] to 0x00 or 0x03:
=== 80 pin miniPCI pad layout ===
* 0x00 is for IFB (InterFace Board, used by [[SKU_Models_Nonretail#Nonretail_prototypes_.28CEB.29|CEB]])
CN3208 80P<br />
* 0x03 is for [[Communication Processor]] (PIF5, used by [[SKU_Models_Nonretail#Reference_tool_prototypes_.28DEHR.29|DEH-R10XX]] and [[DECR-1000]])
** Does also have support for '''all''' ''retail platforms'' (e.g. [[COK-00x#COK-001|COK-001]], [[VER-00x#VER-001|VER-001]] or [[RTX-00x#RTX-001|RTX-001]])


Supported devices:
{| class="wikitable sortable"
{| class="wikitable sortable"
|-
|-
! Device ID !! Device "Name" !! Firmware
! 80P<br />Pin !! Usage !! 100P<br />Pin !! 124P<br />Pin !! Remark
|-
|-
| 104D8183 || Sony IFB ATHENS Board Revision 0x1 || [[010.???]] to {{latestPS3}}
| 01 || +3.3V_PCI || 03, 08, 12, 15, 24, 47, 54, 72, 73 || 19, 24, 28, 31, 40, 63, 70, 88, 89 (not 124) || VCC
|-
|-
| 104D81FF || Sony PIF5 [[TMR-520|TMR]] Board Revision 0x101 || [[0.6.0.004.r010|060.004]] to {{latestPS3}}
| 02 || GND || 7, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 104D8200 || Sony DVE (RSX Tracing) FPGA || [[0.8.2.006.r010|082.006]] to {{latestPS3}}
| 03 || PIO15 || ||  || ?
|-
|-
| 104D820E || Sony [[CXD9208GP]] PS2 emulation subsystem adapter || [[0.8.2.006.r010|082.006]] to {{latestPS3}}
| 04 || PIO11 || ||  || ?
|-
|-
| 80861076 || Intel 82541PI Gigabit Ethernet Controller || [[010.???]] to {{latestPS3}}
| 05 || PIO14 ||  ||  || ?
|-
|-
|}
| 06 || PIO10 ||  ||  || ?
 
Major differences from PCI standard:
* smaller formfactor (80 pin, instead of miniPCI 100P-type I/II or MiniPCI 124P-Type III)
* no use of miniPCI standard sideband signals for audio and communications
* no support of the miniPCI standard CLKRUN# signal defined in the PCI Mobile Design Guide
* no support for optional JTAG signals, nor for the 64-bit PCI extension defined in the PCI Local Bus Specification
 
=== 70/80 pin miniPCI pad layout ===
CN3208 80P on [[CECHAxx]]/[[CECHBxx]] [[COK-00x#COK-001|COK-001]], [[CECHCxx]]/[[CECHExx]] [[COK-00x#COK-002|COK-002(W)]], [[CECH-20xx]] [[DYN-00x#DYN-001|DYN-001]] and '''all''' [[Motherboard_Revisions#DYN-001|later models]]
 
CN3208 70P on [[CECHGxx]] [[SEM-00x#SEM-001|SEM-001]], [[CECHHxx]] [[DIA-00x#DIA-001|DIA-001]], [[CECHJxx]]/[[CECHKxx]] [[DIA-00x#DIA-002|DIA-002]] and [[CECHLxx]]/[[CECHMxx]]/[[CECHPxx]]/[[CECHQxx]] [[VER-00x#VER-001|VER-001]]
 
{| class="wikitable sortable"
|-
! 80P<br />Pin !! 70P<br />Pin !! Usage !! 100P<br />Pin<br />(Type I/II) !! 124P<br />Pin<br />(Type III) !! Remark
|-
| 01 || 35 || +3.3V_PCI || 03, 08, 12, 15, 24, 47, 54, 72, 73 || 19, 24, 28, 31, 40, 63, 70, 88, 89 (not 124) || VCC
|-
| 02 || 70 || GND || 7, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
| 03 || - || PIO15 ||  ||  || ?
|-
| 04 || - || PIO11 ||  ||  || ?
|-
| 05 || - || PIO14 ||  ||  || ?
|-
| 06 || - || PIO10 ||  ||  || ?
|-
| 07 || - || PIO13 ||  ||  || ?
|-
| 08 || - || PIO9 ||  ||  || ?
|-
| 09 || - || PIO12 ||  ||  || ?
|-
| 10 || - || PIO8 ||  ||  || ?
|-
|-
| 11 || 01 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 07 || PIO13 || || || ?
|-
|-
| 12 || 36 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 08 || PIO9 || || || ?
|-
|-
| 13 || 02 || /INTA || 04 || 20 || Interrupt line A (open-drain)
| 09 || PIO12 || || || ?
|-
|-
| 14 || 37 || /INTB || 01 || 17 || Interrupt line B (open-drain)
| 10 || PIO8 || || || ?
|-
|-
| 15 || 03 || /INTC || - || - || Interrupt line C (open-drain)
| 11 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 16 || 38 || /INTD || - || - || Interrupt line D (open-drain)
| 12 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 17 || 04 || /RST || 10 || 26 || Reset
| 13 || /INTA || 04 || 20 || Interrupt line A (open-drain)
|-
|-
| 18 || 39 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 14 || /INTB || 01 || 17 || Interrupt line B (open-drain)
|-
|-
| 19 || 05 || /GNT || 14 || 30 || Bus grant from motherboard to card
| 15 || /INTC || - || - || Interrupt line C (open-drain)
|-
|-
| 20 || 40 || CLK || 09 || 25 ||  
| 16 || /INTD || - || - || Interrupt line D (open-drain)
|-
|-
| 21 || 06 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 17 || /RST || 10 || 26 || Reset
|-
|-
| 22 || 41 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 18 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 23 || 07 || /PME || 18 || 34 || Power management event. 3.3 V, open drain, active low
| 19 || /GNT || 14 || 30 || Bus grant from motherboard to card
|-
|-
| 24 || 42 || /REQ || || || Bus request from card to motherboard
| 20 || CLK || 09 || 25 ||  
|-
|-
| 25 || 08 || AD30 || 22 || 38 || Address/Data 30
| 21 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 26 || 43 || AD31 || 17 || 33 || Address/Data 31
| 22 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 27 || 09 || AD28 || 26 || 42 || Address/Data 28
| 23 || /PME || 18 || 34 || Power management event. 3.3 V, open drain, active low
|-
|-
| 28 || 44 || AD29 || 19 || 35 || Address/Data 29
| 24 || /REQ || || || Bus request from card to motherboard
|-
|-
| 29 || 10 || AD26 || 28 || 44 || Address/Data 26
| 25 || AD30 || 22 || 38 || Address/Data 30
|-
|-
| 30 || 45 || AD27 || 23 || 39 || Address/Data 27
| 26 || AD31 || 17 || 33 || Address/Data 31
|-
|-
| 31 || 11 || AD24 || 30 || 46 || Address/Data 24
| 27 || AD28 || 26 || 42 || Address/Data 28
|-
|-
| 32 || 46 || AD25 || 25 || 41 || Address/Data 25
| 28 || AD29 || 19 || 35 || Address/Data 29
|-
|-
| 33 || 12 || IDSEL || || || IDSEL is asserted by PCI system to select the connected device during configuration read and write transactions.
| 29 || AD26 || 28 || 44 || Address/Data 26
|-
|-
| 34 || 47 || /C/BE3 ||  || || Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
| 30 || AD27 || 23 || 39 || Address/Data 27
|-
|-
| 35 || 13 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 31 || AD24 || 30 || 46 || Address/Data 24
|-
|-
| 36 || 48 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 32 || AD25 || 25 || 41 || Address/Data 25
|-
|-
| 37 || 14 || AD22 || 36 || 52 || Address/Data 22
| 33 || IDSEL || || || IDSEL is asserted by PCI system to select the connected device during configuration read and write transactions.
|-
|-
| 38 || 49 || AD23 || 31 || 47 || Address/Data 23
| 34 || /C/BE3 || || || Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
|-
| 39 || 15 || AD20 || 38 || 54 || Address/Data 20
| 35 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 40 || 50 || AD21 || 35 || 51 || Address/Data 21
| 36 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 41 || 16 || AD18 || 42 || 58 || Address/Data 18
| 37 || AD22 || 36 || 52 || Address/Data 22
|-
|-
| 42 || 51 || AD19 || 37 || 53 || Address/Data 19
| 38 || AD23 || 31 || 47 || Address/Data 23
|-
|-
| 43 || 17 || AD16 || 44 || 60 || Address/Data 16
| 39 || AD20 || 38 || 54 || Address/Data 20
|-
|-
| 44 || 52 || AD17 || 41 || 57 || Address/Data 17
| 40 || AD21 || 35 || 51 || Address/Data 21
|-
|-
| 45 || 18 || /FRAME || 48 || 64 || FRAME is driven by the current master to indicate the beginning and duration of an access. While FRAME is asserted, data transaction continues. When FRAME is deasserted, the transaction is in the final data phase.
| 41 || AD18 || 42 || 58 || Address/Data 18
|-
|-
| 46 || 53 || /C/BE2 || 43 || 59 || Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
| 42 || AD19 || 37 || 53 || Address/Data 19
|-
|-
| 47 || 19 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 43 || AD16 || 44 || 60 || Address/Data 16
|-
|-
| 48 || 54 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 44 || AD17 || 41 || 57 || Address/Data 17
|-
|-
| 49 || 20 || /TRDY || 50 || 66 || TRDY indicates the PCI bus slave can complete the current data phase of the transaction.
| 45 || /FRAME || 48 || 64 || FRAME is driven by the current master to indicate the beginning and duration of an access. While FRAME is asserted, data transaction continues. When FRAME is deasserted, the transaction is in the final data phase.
|-
|-
| 50 || 55 || /IORDY || 45 || 61 || IRDY indicates the PCI bus master can complete the current data phase of the transaction.
| 46 || /C/BE2 || 43 || 59 || Command/Byte Enable 3 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
|-
| 51 || 21 || /STOP || 52 || 68 || STOP indicates the connected device is requesting that the current master stop the current transaction.
| 47 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 52 || 56 || /DEVSEL || 56 || 72 || The connected device drives this signal active to indicate that it has decoded its address as the target of the current access.
| 48 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 53 || 22 || PAR || 40 || 56 || The connected device drives PAR in read data phases for parity checking.
| 49 || /TRDY || 50 || 66 || TRDY indicates the PCI bus slave can complete the current data phase of the transaction.
|-
|-
| 54 || 57 || /PERR || 55 || 71 || The PERR pin reports data parity errors during data read phases. Even parity over AD[31:00] and C/BE[3:0]#
| 50 || /IORDY || 45 || 61 || IRDY indicates the PCI bus master can complete the current data phase of the transaction.
|-
|-
| 55 || 23 || AD15 || 60 || 76 || Address/Data 15
| 51 || /STOP || 52 || 68 || STOP indicates the connected device is requesting that the current master stop the current transaction.
|-
|-
| 56 || 58 || /SERR || 51 || 67 || System error
| 52 || /DEVSEL || 56 || 72 || The connected device drives this signal active to indicate that it has decoded its address as the target of the current access.
|-
|-
| 57 || 24 || AD13 || 62 || 78 || Address/Data 13
| 53 || PAR || 40 || 56 || The connected device drives PAR in read data phases for parity checking.
|-
|-
| 58 || 59 || /C/BE1 || 57 || 73 || Command/Byte Enable 1 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
| 54 || /PERR || 55 || 71 || The PERR pin reports data parity errors during data read phases. Even parity over AD[31:00] and C/BE[3:0]#
|-
|-
| 59 || 25 || AD11 || 64 || 80 || Address/Data 11
| 55 || AD15 || 60 || 76 || Address/Data 15
|-
|-
| 60 || 60 || AD14 || 59 || 75 || Address/Data 14
| 56 || /SERR || 51 || 67 || System error
|-
|-
| 61 || 26 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 57 || AD13 || 62 || 78 || Address/Data 13
|-
|-
| 62 || 61 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 58 || /C/BE1 || 57 || 73 || Command/Byte Enable 1 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
|-
| 63 || 27 || AD09 || 68 || 84 || Address/Data 09
| 59 || AD11 || 64 || 80 || Address/Data 11
|-
|-
| 64 || 62 || AD12 || 63 || 79 || Address/Data 12
| 60 || AD14 || 59 || 75 || Address/Data 14
|-
|-
| 65 || 28 || /C/BE0 || 70 || 86 || Command/Byte Enable 0 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
| 61 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 66 || 63 || AD10 || 65 || 81 || Address/Data 10
| 62 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 67 || 29 || AD06 || 74 || 90 || Address/Data 06
| 63 || AD09 || 68 || 84 || Address/Data 09
|-
|-
| 68 || 64 || AD08 || 69 || 85 || Address/Data 08
| 64 || AD12 || 63 || 79 || Address/Data 12
|-
|-
| 69 || 30 || AD04 || 76 || 92 || Address/Data 04
| 65 || /C/BE0 || 70 || 86 || Command/Byte Enable 0 // These inputs are the multiplexed Bus Command and Byte Enable signals on the PCI bus.
|-
|-
| 70 || 65 || AD07 || 71 || 87 || Address/Data 07
| 66 || AD10 || 65 || 81 || Address/Data 10
|-
|-
| 71 || 31 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 67 || AD06 || 74 || 90 || Address/Data 06
|-
|-
| 72 || 66 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
| 68 || AD08 || 69 || 85 || Address/Data 08
|-
|-
| 73 || 32 || AD02 || 78 || 94 || Address/Data 02
| 69 || AD04 || 76 || 92 || Address/Data 04
|-
|-
| 74 || 67 || AD05 || 75 || 91 || Address/Data 05
| 70 || AD07 || 71 || 87 || Address/Data 07
|-
|-
| 75 || 33 || AD00 || 80 || 96 || Address/Data 00
| 71 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 76 || 68 || AD03 || 79 || 95 || Address/Data 03
| 72 || GND || 07, 11, 16, 21, 33, 34, 39, 46, 53, 58, 61, 66, 67, 85, 86, 98 || 23, 27, 32, 37, 49, 50, 55, 62, 69, 74, 77, 82, 83, 101, 102, 114 || Ground
|-
|-
| 77 || - || SIORXD[0] || || || Southbridge Serial Receive
| 73 || AD02 || 78 || 94 || Address/Data 02
|-
|-
| 78 || 69 || AD01 || 83 || 99 || Address/Data 01
| 74 || AD05 || 75 || 91 || Address/Data 05
|-
|-
| 79 || - || SIOTXD[0] ||  ||  || Southbridge Serial Transceive
| 75 || AD00 || 80 || 96 || Address/Data 00
|-
| 80 || 34 || /SW_PCI ||  ||  || ?switch PCI?
|-
|}
 
==== [[South Bridge]] serial ====
{| class="wikitable sortable"
|-
|-
! Pad !! Name !! Usage !! Remark
| 76 || AD03 || 79 || 95 || Address/Data 03
|-
|-
| JL9385 || +3.3V_SB_VDDIO || VCC ||  
| 77 || SIORXD[0] || || || ?Serial Receive?
|-
|-
| JL9386 || GND || Ground ||  
| 78 || AD01 || 83 || 99 || Address/Data 01
|-
|-
| JL9387 || SB_SIO0-RXD || Receive ||  
| 79 || SIOTXD[0] || || || ?Serial Transceive?
|-
|-
| JL9388 || SB_SIO0-TXT || Tranceive ||  
| 80 || /SW_PCI || || || ?switch PCI?
|-
|-
|}
|}
=== 160 pin pad layout ===
CN4301 160P on [[DECR-1000]] [[TMU-520]] (only partly used for PCI)<br />
'''TODO'''
{{Wikify}}
{{Motherboard Components}}<noinclude>[[Category:Main]]</noinclude>
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)