Editing GbLAN

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
[[Category:Hardware]]
= Gigabit LAN =
= Gigabit LAN =


Line 9: Line 10:
! Ports !! Size !! Speed !! Voltage !! Packaging !! Manufacturer !! Serial Number !! Description
! Ports !! Size !! Speed !! Voltage !! Packaging !! Manufacturer !! Serial Number !! Description
|-
|-
| 8 (3 used) || 20x20mm || Xtal X3501: 25MHz || 3.3V/1.9V/1.2V || 144-pin TQFP || Marvell Alaska || [[88E6108-LAR1]] || Used in earlier models (up to [[CECHGxx]]/[[SEM-00x|SEM-001]])
| 8 (3 used) || 20x20mm || Xtal X3501: 25MHz || 3.3V/1.9V/1.2V || 144-pin TQFP || Marvell || 88E6108-LAR1 || Used in earlier models (up to CECHG/SEM-001)
|-
|-
| ? || ? || ? || ? || ? || Marvell Alaska || [[88E6106-LKJ1]] || Used in later models ([[CECHHxx]]/[[DIA-00x|DIA-001]])
| ? || ? || ? || ? || ? || Marvell || 88E6106-LKJ1 || Used in later models (CECHH/DIA-001)
|-
|-
| ? || ? || ? || ? || ? || ? || ? || DIA-002 (CECHJxx, CECHKxx)
| - || - || 125MHz || 3.3V, 2.5V or 1.8V || 64-pin QFN || Marvell || Alaska 88E1118R-NNC2 || Used in Slim models (CECH-20..A/DYN-001)
|-
|-
| ? || ? || ? || ? || ? || ? || ? || VER-001 (CECHLxx, CECHMxx, CECHPxx, CECHQxx)
|}
:
 
 
=== Marvell 88E6108-LAR1 ===
 
<div style="float:right">[[File:Marvell 88E6108-LAR1.JPG|200px|thumb|left|144-TQFP<br />Marvell 88E6108-LAR1]]</div>
 
Datasheet: (not available)
 
<pre>productcode meaning:
88E6108-LAR1
 
Type: Ethernet
Speed : 1Gbps
Ports : 8
Package : 144-TQFP
 
(sorry, no explaination yet)</pre>
 
The Marvell 88E6108-LAR1 is sort of a switching hub chip, with several ports that can be used in different configurations:
<pre>Port 0 (usuable as MDI 4 dif.pair) : unused (tied to ground)
Port 1 (usuable as MDI 4 dif.pair) : unused (tied to ground)
Port 2 (usuable as MDI 4 dif.pair) : wired to external UTP connector
Port 3 (GMII): Wired to SB
Port 4 (usable as TX/RX dif.pair)(100FX): wired to Wifi
Port 5 (usable as TX/RX dif.pair): unused (tied to ground)
Port 6 (usable as TX/RX dif.pair): unused (tied to ground)
Port 7 (usable as TX/RX dif.pair): unused (tied to ground)</pre>
 
==== Pinout IC3503====
Productcode: 88E6108-B2-LAR1C000-P123 | PartNo.: 6-710-202-01
<div style="height:400px; overflow:auto">
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"
|- bgcolor="#cccccc"
! Pin # !! Name !! Port !! Description
|-
| 1 || RST || rowspan="36" | Power / Led / Xtal etc || -
|-
| 2 || AVDD || -
|-
| 3 || NC || No Connection
|-
| 4 || NC || No Connection
|-
| 5 || NC || No Connection
|-
| 6 || AVDD || -
|-
| 7 || XTAL_IN || -
|-
| 8 || XTAL_OUT || -
|-
| 9 || VDD_CORE || -
|-
| 10 || NC || No Connection
|-
| 11 || NC || No Connection
|-
| 12 || AVDD || -
|-
| 13 || NC || No Connection
|-
| 14 || NC || No Connection
|-
| 15 || P0_LED3 || -
|-
| 16 || P0_LED2 || -
|-
| 17 || VDD_CORE || -
|-
| 18 || P0_LED1 || -
|-
|-
| - || - || 125MHz || 3.3V, 2.5V or 1.8V || 64-pin QFN || Marvell Alaska || [[88E1118R-NNC2]] || Used in Slim models ([[CECH-20xx]]/[[DYN-00x]] and [[CECH-21xx]]/[[SUR-00x|SUR-001]])
| 19 || P0_LED0 || -
|-
|-
| - || 6,5x6,5mm || - || - || 48-pin || Marvell Alaska || [[88E1310-NNB2]] || Used in Slim models ([[CECH-25xx]]/[[JTP-00x|JTP-001]]/[[JSD-00x|JSD-001]], [[CECH-30xx]]/[[KTE-00x|KTE-001]])
| 20 || VDDO_LED || -
|-
|-
| ? || ? || ? || ? || ? || ? || ? || superslims ?
| 21 || P1_LED3 || -
|-
| 22 || VDD_CORE || -
|-
| 23 || P1_LED3 || -
|-
| 24 || P1_LED1 || -
|-
| 25 || P1_LED0 || -
|-
| 26 || VDDO_LED || -
|-
| 27 || P2_LED3 || -
|-
| 28 || P2_LED2 || -
|-
| 29 || P2_LED1 || -
|-
| 30 || P2_LED0 || -
|-
| 31 || VDD_CORE || -
|-
| 32 || MDC_PHY/PPU_EN || -
|-
| 33 || VDDO_SMI_PHY || -
|-
| 34 || MDIO_PHY || -
|-
| 35 || VDD_PLL || -
|-
| 36 || VDD_CORE || -
|-
| 37 || P7_TXP || rowspan="5" | Port 7<br />(unused) || -
|-
| 38 || P7_TXN || -
|-
| 39 || P7_VDDAH || Ground
|-
| 40 || P7_RXP || -
|-
| 41 || P7_RXN || -
|-
| 42 || VSS || || Ground
|-
| 43 || P6_RXP || rowspan="5" | Port 6<br />(unused) || -
|-
| 44 || P6_RXN || -
|-
| 45 || P6_VDDAH || Ground
|-
| 46 || P6_TXN || -
|-
| 47 || P6_TXP || -
|-
| 48 || VDD_CORE || || -
|-
| 49 || P5_TXP || rowspan="5" | Port 5<br />(unused) || -
|-
| 50 || P5_TXN || -
|-
| 51 || P5_VDDAH || Ground
|-
| 52 || P5_RXP || -
|-
| 53 || P5_RXN || -
|-
| 54 || VSS || || Ground
|-
| 55 || P4_RXN || rowspan="5" | Port 4 (100FX) || -
|-
| 56 || P4_RXP || -
|-
| 57 || P4_VDDAH || -
|-
| 58 || P4_TXN || -
|-
| 59 || P4_TXP || -
|-
| 60 || VDD_CORE || || -
|-
| 61 || VDD_P3 || rowspan="46" | Port 3 (GMII) || -
|-
| 62 || P3_CLK125N || -
|-
| 63 || P3_TXEN/HALFDPX || -
|-
| 64 || P3_TXD7/MODE2 || -
|-
| 65 || P3_TXD6/MODE1 || -
|-
| 66 || VDD_CORE || -
|-
| 67 || P3_TXD5/MODE0 || -
|-
| 68 || P3_TXD4/ADDR4 || -
|-
| 69 || VDD0_P3 || -
|-
| 70 || P3_TXD3/ADDR3 || -
|-
| 71 || P3_TXD2/ADDR2 || -
|-
| 72 || P3_TXD1/ADDR1 || -
|-
| 73 || P3_TXD0/ADDR0 || -
|-
| 74 || P3_TXCLK || -
|-
| 75 || P3_GTXCLK || -
|-
| 76 || VDD0_P3 || -
|-
| 77 || P3_RXDV || -
|-
| 78 || VDD_CORE || -
|-
| 79 || P3_RXXEA || -
|-
| 80 || P3_RXD7 || -
|-
| 81 || P3_RXD6 || -
|-
| 82 || P3_RXD5 || -
|-
| 83 || P3_RXD4 || -
|-
| 84 || VDD_CORE || -
|-
| 85 || P3_RXD3 || -
|-
| 86 || VDDO_P3 || -
|-
| 87 || P3_RXD2 || -
|-
| 88 || P3_RXD1 || -
|-
| 89 || P3_RXD0 || -
|-
| 90 || P3_RXCLK || -
|-
| 91 || VDD_CORE || -
|-
| 92 || P3_CRS || -
|-
| 93 || P3_COL || -
|-
| 94 || P3_ENABLE_PD || -
|-
| 95 || INTn || -
|-
| 96 || MDIO_CPU || -
|-
| 97 || MDC_CPU || -
|-
| 98 || VDD_CORE || -
|-
| 99 || EE_DOUT || -
|-
| 100 || VDDO_SMI_CPU || -
|-
| 101 || EE_DIN/HD_FLOW_DIS || -
|-
| 102 || EE_CLK/FD_FLOW_DIS || -
|-
| 103 || EE_CS/EE_1K || -
|-
| 104 || VDD_CORE || -
|-
| 105 || SW_MODE0 PU || -
|-
| 106 || SW_MODE1 PU || -
|-
| 107 || VSS ||  || Ground
|-
| 108 || RESETn ||  || -
|-
| 109 || VSS || rowspan="12" | Port 2 (MDI) || Ground
|-
| 110 || P2_MDIN3 || -
|-
| 111 || P2_MDIP3 || -
|-
| 112 || P2_AVDD || -
|-
| 113 || P2_MDIN2 || -
|-
| 114 || P2_MDIP2 || -
|-
| 115 || P2_MDIN1 || -
|-
| 116 || P2_MDIP1 || -
|-
| 117 || P2_AVDD || -
|-
| 118 || P2_AVDD || -
|-
| 119 || P2_MDIN0 || -
|-
| 120 || P2_MDIP0 || -
|-
| 121 || VSS || rowspan="12" | Port 1 (MDI) || Ground
|-
| 122 || P1_MDIN3 || -
|-
| 123 || P1_MDIP3 || -
|-
| 124 || P1_AVDD || -
|-
| 125 || P1_MDIN2 || -
|-
| 126 || P1_MDIP2 || -
|-
| 127 || P1_MDIN1 || -
|-
| 128 || P1_MDIP1 || -
|-
| 129 || P1_AVDD || -
|-
| 130 || P1_AVDD || -
|-
| 131 || P1_MDIN0 || -
|-
| 132 || P1_MDIP0 || -
|-
| 133 || VSS || rowspan="12" | Port 0 (MDI) || Ground
|-
| 134 || P0_MDIN3 || -
|-
| 135 || P0_MDIP3 || -
|-
| 136 || P0_AVDD || -
|-
| 137 || P0_MDIN2 || -
|-
| 138 || P0_MDIP2 || -
|-
| 139 || P0_MDIN1 || -
|-
| 140 || P0_MDIP1 || -
|-
| 141 || P0_AVDD || -
|-
| 142 || P0_AVDD || -
|-
| 143 || P0_MDIN0 || -
|-
| 144 || P1_MDIP0 || -
|-
|}
</div>
 
 
==== Pinout CN3501 ====
Connectortype: RJ45 modular jack with LED | PartNo.: 1-820-763-12
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"
|- bgcolor="#cccccc"
! Pin # !! Name !! Description
|-
| 1 || VCC || -
|-
| 2 || TP1+ || -
|-
| 3 || TP1- || -
|-
| 4 || TP2+ || -
|-
| 5 || TP2- || -
|-
| 6 || GND || -
|-
| 7 || TP3+ || -
|-
| 8 || TP3- || -
|-
| 9 || TP4+ || -
|-
| 10 || TP4- || -
|-
| 11 || VCC || -
|-
|-
|}
|}
:


== Jumbo frames ==
=== Marvell 88E6106-LKJ1 ===
From Linux perspective (under OtherOS &lt;=3.15), the old drivers set the [http://git.kernel.org/?p=linux/kernel/git/next/linux-next.git;a=blob;f=drivers/net/ps3_gelic_net.h;h=5e1c28654e16146918a70e2efbbd3da4619a939f;hb=02c1889166b47b9ade309a8f4b7c4ddf0489d869#l44 MTU to 2308], while newer versions set the [http://git.kernel.org/?p=linux/kernel/git/next/linux-next.git;a=blob;f=drivers/net/ps3_gelic_net.h;h=d9a55b93898b24f2b67a6f54accc5ee064d79bbb;hb=HEAD#l35 MTU of 1518]. This could be a hypervisor restriction (needs research).
-nothing yet-
 
 
=== Marvell Alaska 88E1118R-NNC2 ===
 
<div style="float:right">
[[File:Marvel-Alaska-88E1118R.PNG|200px|thumb|left|Marvel Alaska 88E1118R<br />As seen on PS3 Slim PCB<br />righthand side goes to backside RJ/UTP connector]]<br />[[File:64-pin-QFN-Marvel-Alaska-88E1118R.PNG|200px|thumb|left|64-pin QFN<br />Marvel Alaska 88E1118R]]</div>
 
[http://www.marvell.com/transceivers/assets/88E1118R_Technical_Product_Brief.pdf Product Brief]
 
<pre>productcode meaning:
88E1118R-NNC2 = 10/100/1000BASE-T PHY with RGMII
 
Type: Ethernet
Speed : 1Gbps
VCC: 1.8V (regulators can be supplied with 1.8V, 2.5V or 3.3V)
I/O: 1.8V, 2.5V or 3.3V
125MHz Clock input
Package : 64-pin QFN
 
(sorry, no explaination yet)</pre>


MTU is set with vsh using syscall net_ioctl (libnet)


On 3.41 firmware, with a [https://gist.github.com/jevinskie/945199a90858319642ded49df632554e modified ps3_gelic driver], frames of 1624 bytes can be sent and frames of 1628 bytes can be received.
==== Pinout 64-pin QFN ====


=== Efficiency ===
<div style="height:400px; overflow:auto">
{| class="wikitable" style="text-align:center;"
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"  
! Frame type !! colspan=2 | Layer 1 overhead !! colspan=2 | Layer 2 overhead !! MTU !! Layer 3 overhead !! Layer 4 overhead !! Payload size !! Total transmitted !! Efficiency
|- bgcolor="#cccccc"
! Pin # !! Name !! Pin Type !! Description
|-
| 1 || CONFIG[1] || I || Hardware Configuration
|-
| 2 || CONFIG[2] || I || Hardware Configuration
|-
| 3 || CONFIG[3] || I || Hardware Configuration
|-
| 4 || CLK125 || O || 125 MHz Clock Output. When Hardware reset is asserted, a 25 MHz clock is generated output, otherwise a 125 MHz clock is output.
|-
| 5 || DVDD || Power || Digital core supply - 1.2V. DVDD can be supplied externally with 1.2, or via the 1.2V regulator.
|-
| 6 || LED[0] || O || LED/Interrupt outputs
|-
| 7 || VDDO || Power || 1.8V, 2.5V, or 3.3V non-RGMII digital I/O supply. VDDO must be supplied externally. Do not use the 1.8V regulator to power VDDO.
|-
| 8 || LED[1] || O || LED/Interrupt outputs
|-
| 9 || LED[2] || O || LED/Interrupt outputs
|-
| 10 || RESETn || I || Hardware reset. Active low. 0 = Reset 1 = Normal
|-
| 11 || TRSTn || I, PU || Boundary scan test reset input. Active low. TRSTn contains an internal 150 kohm pull-up resistor as per the 1149.1 specification. After power up, the JTAG state machine should be reset by applying a low signal on this pin, or by keeping TMS high and applying 5 TCK pulses, or by pulling this pin low by a 4.7 kohm resistor.
|-
| 12 || DIS_REG12 || I || 1.2V Regulator Disable. Tie to VDDO to disable, tie to VSS to enable.
|-
| 13 || DVDD || Power || Digital core supply - 1.2V. DVDD can be supplied externally with 1.2, or via the 1.2V regulator.
|-
| 14 || AVDDR || || 1.2V Regulator supply - 1.8V  AVDDR can be supplied externally with 1.8V, or via the 1.8V regulator. If the 1.2V regulator is not used, AVDDR must still be tied to 1.8V.
|-
| 15 || AVDDR || || 1.2V Regulator supply - 1.8V  AVDDR can be supplied externally with 1.8V, or via the 1.8V regulator. If the 1.2V regulator is not used, AVDDR must still be tied to 1.8V.
|-
| 16 || AVDDX || Power || 1.8V Regulator supply - 2.5V, 3.3V, (or 1.8V). AVDDX must be supplied externally. Note that this supply must be the same voltage as AVDDC. If the 1.8V regulator is not used, then it means a 1.8V supply is in the system. AVDDX (along with AVDDC) would be tied to 1.8V in this case.
|-
| 17 || CTRL18 || O || 1.8V Regulator Control. This signal ties to the base of the BJT. If the 1.8V regulator is not used it can be left floating.
|-
| 18 || NC || NC || No connect. These pins are not connected to the die so they can be connected to anything on the board.
|-
| 19 || MDIN[3] || I/O, D || Media Dependent Interface[3]
|-
| 20 || MDIP[3] || I/O, D || Media Dependent Interface[3]
|-
| 21 || AVDD || Power || Analog supply. 1.8V. AVDD can be supplied externally with 1.8V, or via the 1.8V regulator.
|-
| 22 || AVDD || Power || Analog supply. 1.8V. AVDD can be supplied externally with 1.8V, or via the 1.8V regulator.
|-
| 23 || MDIN[2] || I/O, D || Media Dependent Interface[2]
|-
| 24 || MDIP[2] || I/O, D || Media Dependent Interface[2]
|-
| 25 || MDIN[1] || I/O, D || Media Dependent Interface[1]
|-
| 26 || MDIP[1] || I/O, D || Media Dependent Interface[1]
|-
| 27 || AVDD || Power || Analog supply. 1.8V. AVDD can be supplied externally with 1.8V, or via the 1.8V regulator.
|-
| 28 || NC || NC || No connect. These pins are not connected to the die so they can be connected to anything on the board.
|-
| 29 || AVDD || Power || Analog supply. 1.8V. AVDD can be supplied externally with 1.8V, or via the 1.8V regulator.
|-
| 30 || MDIN[0] || I/O, D || Media Dependent Interface[0]
|-
| 31 || MDIP[0] || I/O, D || Media Dependent Interface[0]
|-
| 32 || TSTPT || O || Test Point
|-
| 33 || RSET || I || Constant voltage reference. External 4.99 kohm 1% resistor connection to VSS required for each pin.
|-
| 34 || AVDDC || || Analog supply - 1.8V or 2.5V, or 3.3V. AVDDC must be supplied externally. Do not use the 1.8V regulator to power AVDDC.
|-
| 35 || HSDACN || O || AC Test Point. Connect the AC testpoints with a 50 ohm termination resistor to VSS for IEEE testing and debug purposes. If debug and IEEE testing are not of importance, these pins can be left floating.
|-
| 36 || HSDACP || O || AC Test Point. Connect the testpoints with a 50 ohm termination resistor to VSS for IEEE testing and debug purposes. If debug and IEEE testing are not of importance, these pins can be left floating.
|-
| 37 || AVDDC || || Analog supply - 1.8V or 2.5V, or 3.3V. AVDDC must be supplied externally. Do not use the 1.8V regulator to power AVDDC.
|-
| 38 || XTAL_IN || I || Reference Clock. 25 MHz ± 50 ppm tolerance crystal reference or oscillator input.
NOTE: If AVDDC is tied to 1.8V, then the XTAL_IN pin is not 2.5V/3.3V tolerant.
If AVDDC is tied to 2.5V, then the XTAL_IN pin is not 3.3V tolerant.
|-
| 39 || XTAL_OUT || O || Reference Clock. 25 MHz ± 50 ppm tolerance crystal reference. When the
XTAL_OUT pin is not connected, it should be left floating.
|-
| 40 || DVDD || Power || Digital core supply - 1.2V. DVDD can be supplied externally with 1.2, or via the 1.2V regulator.
|-
| 41 || TMS || I, PU || Boundary scan test mode select input. TMS contains an internal 150 kohm pull-up resistor.
|-
| 42 || TCK || I, PU || Boundary scan test clock input. TCK contains an internal 150 kohm pull-up resistor.
|-
| 43 || TDI || I || Boundary scan test data input
|-
| 44 || TDO || O || Boundary scan test data output
|-
| 45 || MDIO || I/O || MDIO is the management data. MDIO transfers management data in and out of the device synchronously to MDC. This pin requires a pull-up resistor in a range from 1.5 kohm to 10 kohm.
|-
| 46 || VDDO || Power || 1.8V, 2.5V, or 3.3V non-RGMII digital I/O supply. VDDO must be supplied externally. Do not use the 1.8V regulator to power VDDO.
|-
| 47 || DVDD || Power || Digital core supply - 1.2V. DVDD can be supplied externally with 1.2, or via the 1.2V regulator.
|-
| 48 || MDC  || I || MDC is the management data clock reference for the serial management interface. A continuous clock stream is not expected. The maximum frequency supported is 8.3 MHz.
|-
| 49 || RX_CTRL || O || RGMII Receive Control. RX_DV is presented on the rising edge of RX_CLK. A logical derivative of RX_DV and RX_ER is presented on the falling edge of RX_CLK.
|-
|-
| Standard || rowspan="4" | preamble<br />8 byte || rowspan="4" | IPG<br />12 byte || rowspan="4" | frame header<br />14 byte || rowspan="4" | FCS<br />4 byte || 1500 || rowspan="4" | IPv4 header<br />20 byte || rowspan="4" | TCP header<br />20 byte || 1460 byte || 1538 byte || {{round|94.928478544}}%
| 50 || RXD[0] || O || RGMII Receive Data
|-
|-
| old gelic || 2308 || 2268 byte || 2346 byte || {{round|96.675191816}}%
| 51 || RXD[1] || O || RGMII Receive Data
|-
|-
| new gelic || 1518 || 1478 byte || 1556 byte || {{round|94.98714653}}%
| 52 || VDDOR || Power || 1.8V, 2.5V, or 3.3V RGMII digital I/O supply. VDDOR must be supplied externally. Do not use the 1.8V regulator to power VDDOR.
|-
|-
| mod gelic || 1624 || 1584 byte || 1662 byte || {{round|95.306859206}}%
| 53 || RX_CLK || O || RGMII Receive Clock provides a 125 MHz, 25 MHz, or 2.5 MHz reference clock with ± 50 ppm tolerance derived from the received data stream depending on speed.
|-
| 54 || RXD[2] || O || RGMII Receive Data
|-
| 55 || RXD[3] || O || RGMII Receive Data
|-
| 56 || VDDOR || Power || 1.8V, 2.5V, or 3.3V RGMII digital I/O supply. VDDOR must be supplied externally. Do not use the 1.8V regulator to power VDDOR.
|-
| 57 || VREF || I || RGMII input voltage reference. Must be set to VDDOR/2 when used as 1.8V HSTL, 2.5V SSTL_2, and 3.3V. Set to VDDOR when used as 2.5V LV CMOS.
|-
| 58 || TXD[0] || I || RGMII Transmit Data
|-
| 59 || TXD[1] || I || RGMII Transmit Data
|-
| 60 || TCX_CLK || I || RGMII Transmit Clock provides a 125 MHz, 25 MHz, or 2.5 MHz reference clock with ± 50 ppm tolerance depending on speed.
|-
| 61 || TXD[2] || I || RGMII Transmit Data
|-
| 62 || TXD[3] || I || RGMII Transmit Data
|-
| 63 || TX_CTRL || I || RGMII Transmit Control. TX_EN is presented on the rising edge of TX_CLK. A logical derivative of TX_EN and TX_ER is presented on the falling edge of TX_CLK.
|-
| 64 || CONFIG[0] || I || Hardware Configuration
|-
| EPAD || VSS || GND || Ground to device. The 64-pin QFN package has an exposed die pad (E-PAD) at its base. This E-PAD must be soldered to VSS.
|-
|-
|}
|}
</div>


== Jumbo frames ==
From Linux perspective (under OtherOS &lt;=3.15), the old drivers set the [http://git.kernel.org/?p=linux/kernel/git/next/linux-next.git;a=blob;f=drivers/net/ps3_gelic_net.h;h=5e1c28654e16146918a70e2efbbd3da4619a939f;hb=02c1889166b47b9ade309a8f4b7c4ddf0489d869#l44 MTU to 2308], while newer versions set the [http://git.kernel.org/?p=linux/kernel/git/next/linux-next.git;a=blob;f=drivers/net/ps3_gelic_net.h;h=d9a55b93898b24f2b67a6f54accc5ee064d79bbb;hb=HEAD#l35 MTU of 1518]. This could be a hypervisor restriction (needs research).


 
MTU is set with vsh using syscall net_ioctl (libnet)
{{Motherboard Components}}<noinclude>[[Category:Main]]</noinclude>
Please note that all contributions to PS3 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS3 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page:

Retrieved from "http://www.psdevwiki.com/ps3/GbLAN"