Editing E3

[[Category:Hardware]][[Category:Software]]
Files @ http://www.ps3devwiki.com/files/flash/Tools/E3/
== E3 Flasher ==
=== Picture Guide ===
<Gallery>
File:01- that's all you need from the Limited package.jpg|01- that's all you need from the Limited package
File:02- Remove the fan screws to detach it from the metal cage.jpg|02- Remove the fan screws to detach it from the metal cage
File:03- cut 2cm from this corner.jpg|03- cut 2cm from this corner
File:04- 2cm cut from the corner.jpg|04- 2cm cut from the corner
File:05- apply masking tape to protect the CLip Flat cable.jpg|05- apply masking tape to protect the CLip Flat cable
File:06- install the Fan with the bottom metal plate and the heatsink screws.jpg|06- install the Fan with the bottom metal plate and the heatsink screws
File:07- don't forget to connect back the FAN plug.jpg|07- don't forget to connect back the FAN plug
File:08- install everything back into the plastic bottom case.jpg|08- install everything back into the plastic bottom case
File:09- now you can access the NOR freely and add manual pressure on the clip while working.jpg|09- now you can access the NOR freely and add manual pressure on the clip while working
File:10- E3 with clip installed and ready for dumping and flashing.jpg|10- E3 with clip installed and ready for dumping and flashing
File:11- E3 board dumping NOR.jpg|11- E3 board dumping NOR
File:12- E3 in Action with PS3 idle on XMB.jpg|12- E3 in Action with PS3 idle on XMB
</Gallery>

== How to ==

=== update E3 Flasher ===
# use blank micro SD card and copy this [http://www.ps3devwiki.com/files/flash/Tools/E3/BIN/2011.10.28%20E3%20Flasher%20Samsung%20Update_Multi_consoles/update.bin update.bin (Samsung update Multi consoles)] on it, then place the micro SD card into the e3 flasher and use the following settings: switches 1 & 2 should be down, switch 3, 4, 5, 6 should be in the up position.(PS3 are "OFF")
# while powering PS3 "ON" will begin automatically the process , you will see the light progess on the indicator from 8x OFF to 8x ON blue led. (once finished all 8 blue leds lights)

=== make a NOR backup ===
# place a blank micro SD card into the e3 flasher and use the following settings: switches 1 & 2 should be down, switch 3 should be in the up position, switches 4, 5 & 6 should also be down.
# while in the xmb press the start button on the flasher and backup process will begin, you will see each light progess on the indicator from 0% to 100% percent. (once finished the lights will flash alternatively)

=== checking the NOR backup for errors ===
(remove the micro SD card from the flasher and place the card in your pc)

(if you have updated the flasher or recently purchased one you will see three backups on the microSD card bkpps30.bin, bkpps31.bin & bkpps32.bin and the e3flasher text log file)

Bytereverse them with Flowrebuilder and use [[Validating flash dumps]]

KEEP THE OTHER BACKUPS SAFE! just incase you do happen to brick your console you might have a chance for recovery..

==== E3 Nor dump checker ====
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;" 
|-
! style="background-color:red;" | <span style="background-color:lightred; color:white; font-size:200%; ">Warning</span>
|-
| style="background-color:white;" | <span style="white; color:red; font-size:150%; text-align:center; ">This tool is known and proven to give false positives on bad dumps that lead to permabricks. 

Use this method: [[Validating flash dumps]] to make sure the dumps are in crisp condition.

You cannot recover from bad flash without proper dumps (e.g. bricking the console beyond repair).<br />
''<small>note: there are  12½ million bits to permabrick a console</small>''</span>
|-
|}

[http://www.multiupload.com/RV3PN9GVTA E3 Nor Dump Checker V1.0.exe (521.7 KB)] <br />
Article: http://www.ps3hax.net/2011/11/released-e3-nor-dump-checker-v1-0-released-tested/

===== Quick bulletproof test =====

does not test:
* bootldr (corrupted binary not detected)
* metldr (corrupted binary not detected)
* bootldr size (both under- and oversize not detected)
* metldr size (both under- and oversize not detected)
* cISD (didn't catch brick-byte error)
* cCSD (didn't catch brick-byte error)
* trvk_prg0 (didn't catch brick-byte error)
* trvk_prg1 (didn't catch brick-byte error)
* trvk_pkg0 (didn't catch brick-byte error)
* trvk_pkg1 (didn't catch brick-byte error)
* eEID (didn't catch brick-byte error)
* cvtrm (didn't catch brick-byte error)
* CELL_EXTNOR_AREA (didn't catch brick-byte error)

partly test:
* ROS0 (but didn't catch brick-byte error)
* ROS1 (but didn't catch brick-byte error)

does test:
* headerprefix ("00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00")
* header ("00 00 00 00 AC 0F FF E0 00 00 00 00 AD DE EF BE")
* header ("FI.I")
* headersuffix "(FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF")
* filetable ("saceru_eoldare.." etc.)

Conclusion : '''USELESS''', brickdumps will still show as 'valid'. <br />

'''[[Recommendation: use]]<span style="white; color:red;"> [http://www.ps3devwiki.com/files/flash/Tools/Flowrebuilder/ Flowrebuilder] instead and common sense like mentioned on [[Hardware_flashing#Generic_Warning|Hardware flashing]] page.'''

====== Added 22 nov 2011 ======
   ''New E3 flasher update released, it will backup bios 3 times automatically.
   We suggest user verify those bios with E3 Nor dump checker, to assure the backup bios is no erro.'' 

'''[[Conclusion:]]<span style="white; color:red;"> Anyone with a flasher (should) know that you can dump it 1 to 1000's times the same bad. Comparing CRC/MD5/SHA1 is not any secure way to validate flash (as mentioned on [[Hardware_flashing#Generic_Warning|Hardware flashing]]). Letting the dumper do it x times, only gives endusers/customers a false sense of reassurance, always a bad idea.'''

=== Downgrade ===
==== Normal E3 downgrade Process ====

1. place the [http://www.ps3devwiki.com/files/flash/Tools/E3/BIN/e3downgrade%20to%20TF%20%20v1.2/e3_downgrade.bin e3_downgrade.bin] and the bkpps3.bin you made on a micro SD Card. 

2. switches 1, 2, 3, 4, 5 should be down and switch 6 (lock/unlock) should be in the up position. while in the xmb press start on the flasher and the programming process will begin you will see each light progess on the indicator from 0% to 100% percent. (once finished the lights will flash alternatively)
 
3. reboot the console and you should see the connect controller using a USB cable screen (if the console just booted back into the xmb you need to manually patch the backup See. Manual E3 downgrade below)

4. assuming the process was sucessful and you see the connect controller screen switch off the console from the back of the playstation using the switch provided with the e3 kit and place your USB downgrade jig in the port closest to the flasher.

5. switch the console back on using the switch provided then quickly press the power and eject button if sucessful the console should power off automatically. (if not repeat the process)

6. copy the [http://www.ps3devwiki.com/files/lv2diag/3.55%20downgrader/FILE1/Lv2diag.self Lv2diag.self (File1)] & [http://www.ps3devwiki.com/files/firmware/MFW-CEX/Downgrader/Rogero-V3.4/ Rogero V3.4]] from step 1 downgrade files onto a usb and place the usb in the same port you used for the downgrade jig (closest to the flasher) turn on the console and the downgrade process should begin. once finnished the console will turn off automatically

7. next copy the [http://www.ps3devwiki.com/files/lv2diag/3.55%20downgrader/FILE2/Lv2diag.self Lv2diag.self (File2)] onto the usb and place the usb in the same port you used in the last process switch on the console and it should switch off automatically after a few seconds. 

8. power the console back on and you should see the connect the controller screen follow the onscreen instructions.

==== Flash Fun downgrade Process ====

 NO SOLDERING NEEDED !!!

1. place the (patched) bkpps3.bin you made on a micro SD Card. 

2. switches  2, 3, 4, 5, 6 should be down and switch 1 (Flash Fun) should be in the up position. (100000) There will be a blackscreen when you start your system, dont worry it is normal. Press start on the flasher and the programming process will begin you will see each light progress on the indicator from 0% to 100% percent. (once finished the lights will flash alternatively)

3. switch off the console from the back of the playstation using the switch provided with the e3 kit and place your USB downgrade jig in the port closest to the flasher.

4. switch the console back on using the switch provided then quickly press the power and eject button if sucessfull the console should power off automatically. (if not repeat the process)

5. copy the [http://www.ps3devwiki.com/files/lv2diag/3.55%20downgrader/FILE1/Lv2diag.self Lv2diag.self (File1)] & [http://www.ps3devwiki.com/files/firmware/MFW-CEX/Downgrader/Rogero-V32/ (Rogero CFW V3.2)] from step 1 downgrade files onto a usb and place the usb in the same port you used for the downgrade jig (closest to the flasher) turn on the console and the downgrade process should begin. once finnished the console will turn off automatically

6. next copy the [http://www.ps3devwiki.com/files/lv2diag/3.55%20downgrader/FILE2/Lv2diag.self Lv2diag.self (File2)] onto the usb and place the usb in the same port you used in the last process switch on the console and it should switch off automatically after a few seconds. 

7. power the console back on and you should see the connect the controller screen follow the onscreen instructions.

==== Manual E3 downgrade v2 ====
E3 dumps are byte reversed, and so must our patches (otherwise we have to reverse, paste the v2 in the REV, reverse back again - using byte reversed patches shortcuts that 'reversing confusion' :P) 

Dump the flash with the E3, you will end up with a .bin file (e.g. bkpps3.bin)

===== Patches to insert for v2 downgrade =====
<div style="float:right">[[File:Flowrebuilder-E3-autopatcher.png|200px|thumb|left|Flowrebuilder : E3 autopatcher]]</div>

http://www.ps3devwiki.com/files/flash/patches/E3%20downgrade/

{|class="wikitable sortable"
|-
! target area !! patch no. !! NOR Offset !! Paste length !! Remarks
|-
| ROS0 || [http://www.ps3devwiki.com/files/flash/patches/E3%20downgrade/patch1-0C0010-7C0010.REV patch1.REV (7 MB)] || 0x0C0010 || 0x6FFFE0 || version string 3.55
|-
| ROS1 || [http://www.ps3devwiki.com/files/flash/patches/E3%20downgrade/patch1-0C0010-7C0010.REV patch1.REV (7 MB)] || 0x7C0010 || 0x6FFFE0 || same as patch1.REV
|-
| trvk_prg0 (0x40000) <br />trvk_prg1 (0x60000)<br />trvk_pkg0 (0x80000) <br />trvk_pkg1 (0xA0000) || [http://www.ps3devwiki.com/files/flash/patches/E3%20downgrade/rvk-040000.REV rvk-040000.REV (512 KB)] || 0x40000 || 0x80000 || one big patch<br />overlapping several area's
|-
|}(above patches in a single package + autopatcher file: [http://www.ps3devwiki.com/files/flash/patches/E3%20downgrade.rar E3%20downgrade.rar]) 

Using autopatcher from Flow Rebuilder:
* select "PATCH a Byte reversed NOR dump or an interleaved and unscrambled NAND dump."
* Select as Input Dump File the <abbr title="bkpps3.bin">unmodified dump</abbr> (AC 0F FF E0 / AD DE EF BE)
* Select as Patch file: E3-downgrader\progskeet_patch.txt

Use the <abbr title="bkpps3.patch.bin">patched file</abbr>, rename to bkpps3.bin, put on SD and use E3 to flash the ps3. Afterwards, use [http://www.ps3devwiki.com/files/firmware/MFW-CEX/Downgrader/Rogero-V3.4/ Rogero CFW V3.4], or any prepatched PUP that has the lv1/hypervisor syscon hashchecks patched out - or use the TCL from the talk/discussion page to patch one yourself) and reinstall the firmware in service mode like any V2 downgrade.

Note: If you wish to extract an E3 dump: Flowrebuilder can bytereverse and extract the NOR dump for you.

To flash a manually patched backup put all the switches on the flasher down and press start while in the XMB

=== E3 debricking ===

* Requires soldering wire from SBE (solderpad on NOR flatcable) to TRISTATE (NORpoint on PS3 motherboard)
* Make sure you have correct firmware on SD/TF card
* E3 switches set as 1:Flash fun, 2: OFW, 3: Prog, 4: microSD, 5: PS3 Flash, 6: Lock with the console power disconnected.
* Turn on console to restore (progress LEDs will light up one by one and blink if successfully).
* Unplug powercable and set 1:Flash fun down to PS3 Mode and turn on the PS3, if everything went fine, it will now be debricked (remember: in case syscon has 3.56+ hashes, you need prepatched LV1, see downgrader guides).<br />
[http://www.mediafire.com/download.php?k8v7a60tjah64i2 English-E3 FLASHER repair method if console bricked.pdf (424.95 KB)]

==== User experiences ====
From my experience soldering a wire to the nor tristate point did nothing, try this method instead. Manually patch your nor backup. Place the patced backup and the e3_downgrade.bin file onto the SD card then put all the switches on the flasher down and hold start and turn on the console. If the console stays on and the flashing process begins when completed after rebooting the console should boot normally on the firmware you were trying to install, if you see two blue flashing lights and the console just turns off  try this.. all switches down except the 6th one (lock/unlock) hold start on the flasher and turn on the console providing that the console stays on once finished flashing '''DO NOT TURN THE CONSOLE OFF''' instead put the last switch down and press start again. once finished reboot and hopefully the console should be back to life.

Edit: Soldering SBE to the Nor Tristate is important, so your PS3 will stay "on" in Flash Fun Mode even when bricked

== Error Codes ==
<table width="100%" align="left"><tr>
<td align="left">[[File:Error_Codes_E3-Flasher.jpg|200px|thumb|left|E3 Flasher Frontpanel]]</td>
</tr></table>
LED Error

 number 1 stands for LED Blinking
 number 0 stands for LED OFF


{| class="wikitable sortable"
|-
! colspan="8" | Error Codes !! Meaning !! Remarks 
|-
| 0 || 0 || 0 || 0 || 0 || 0 || 0 || 0 || 
|-
| 0 || 0 || 0 || 0 || 0 || 0 || 0 || 1 || 
|-
| 0 || 0 || 0 || 0 || 0 || 0 || 1 || 0 || 
|-
| 0 || 0 || 0 || 0 || 0 || 0 || 1 || 1 || 
|-
| 0 || 0 || 0 || 0 || 0 || 1 || 0 || 0 || 
|-
| 0 || 0 || 0 || 0 || 0 || 1 || 0 || 1 || 
|-
| 0 || 0 || 0 || 0 || 0 || 1 || 1 || 0 || 
|-
| 0 || 0 || 0 || 0 || 0 || 1 || 1 || 1 || 
|-
| 0 || 0 || 0 || 0 || 1 || 0 || 0 || 0 || 
|-
| 0 || 0 || 0 || 0 || 1 || 0 || 0 || 1 || 
|-
| 0 || 0 || 0 || 0 || 1 || 0 || 1 || 0 || 
|-
| 0 || 0 || 0 || 0 || 1 || 0 || 1 || 1 || 
|-
| 0 || 0 || 0 || 0 || 1 || 1 || 0 || 0 || 
|-
| 0 || 0 || 0 || 0 || 1 || 1 || 0 || 1 || 
|-
| 0 || 0 || 0 || 0 || 1 || 1 || 1 || 0 || 
|-
| 0 || 0 || 0 || 0 || 1 || 1 || 1 || 1 || 
|-
| 0 || 0 || 0 || 1 || 0 || 0 || 0 || 0 || 
|-
| 0 || 0 || 0 || 1 || 0 || 0 || 0 || 1 || 
|-
| 0 || 0 || 0 || 1 || 0 || 0 || 1 || 0 || 
|-
| 0 || 0 || 0 || 1 || 0 || 0 || 1 || 1 || 
|-
| 0 || 0 || 0 || 1 || 0 || 1 || 0 || 0 || 
|-
| 0 || 0 || 0 || 1 || 0 || 1 || 0 || 1 || 
|-
| 0 || 0 || 0 || 1 || 0 || 1 || 1 || 0 || 
|-
| 0 || 0 || 0 || 1 || 0 || 1 || 1 || 1 || 
|-
| 0 || 0 || 0 || 1 || 1 || 0 || 0 || 0 || 
|-
| 0 || 0 || 0 || 1 || 1 || 0 || 0 || 1 || 
|-
| 0 || 0 || 0 || 1 || 1 || 0 || 1 || 0 || 
|-
| 0 || 0 || 0 || 1 || 1 || 0 || 1 || 1 || 
|-
| 0 || 0 || 0 || 1 || 1 || 1 || 0 || 0 || 
|-
| 0 || 0 || 0 || 1 || 1 || 1 || 0 || 1 || 
|-
| 0 || 0 || 0 || 1 || 1 || 1 || 1 || 0 || 
|-
| 0 || 0 || 0 || 1 || 1 || 1 || 1 || 1 || 
|-
| 0 || 0 || 1 || 0 || 0 || 0 || 0 || 0 || 
|-
| 0 || 0 || 1 || 0 || 0 || 0 || 0 || 1 || 
|-
| 0 || 0 || 1 || 0 || 0 || 0 || 1 || 0 || 
|-
| 0 || 0 || 1 || 0 || 0 || 0 || 1 || 1 || 
|-
| 0 || 0 || 1 || 0 || 0 || 1 || 0 || 0 || 
|-
| 0 || 0 || 1 || 0 || 0 || 1 || 0 || 1 || 
|-
| 0 || 0 || 1 || 0 || 0 || 1 || 1 || 0 || 
|-
| 0 || 0 || 1 || 0 || 0 || 1 || 1 || 1 || 
|-
| 0 || 0 || 1 || 0 || 1 || 0 || 0 || 0 || 
|-
| 0 || 0 || 1 || 0 || 1 || 0 || 0 || 1 || 
|-
| 0 || 0 || 1 || 0 || 1 || 0 || 1 || 0 || 
|-
| 0 || 0 || 1 || 0 || 1 || 0 || 1 || 1 || 
|-
| 0 || 0 || 1 || 0 || 1 || 1 || 0 || 0 || 
|-
| 0 || 0 || 1 || 0 || 1 || 1 || 0 || 1 || 
|-
| 0 || 0 || 1 || 0 || 1 || 1 || 1 || 0 || 
|-
| 0 || 0 || 1 || 0 || 1 || 1 || 1 || 1 || 
|-
| 0 || 0 || 1 || 1 || 0 || 0 || 0 || 0 || 
|-
| 0 || 0 || 1 || 1 || 0 || 0 || 0 || 1 || 
|-
| 0 || 0 || 1 || 1 || 0 || 0 || 1 || 0 || 
|-
| 0 || 0 || 1 || 1 || 0 || 0 || 1 || 1 || 
|-
| 0 || 0 || 1 || 1 || 0 || 1 || 0 || 0 || 
|-
| 0 || 0 || 1 || 1 || 0 || 1 || 0 || 1 || 
|-
| 0 || 0 || 1 || 1 || 0 || 1 || 1 || 0 || 
|-
| 0 || 0 || 1 || 1 || 0 || 1 || 1 || 1 || 
|-
| 0 || 0 || 1 || 1 || 1 || 0 || 0 || 0 || 
|-
| 0 || 0 || 1 || 1 || 1 || 0 || 0 || 1 || 
|-
| 0 || 0 || 1 || 1 || 1 || 0 || 1 || 0 || 
|-
| 0 || 0 || 1 || 1 || 1 || 0 || 1 || 1 || 
|-
| 0 || 0 || 1 || 1 || 1 || 1 || 0 || 0 || 
|-
| 0 || 0 || 1 || 1 || 1 || 1 || 0 || 1 || 
|-
| 0 || 0 || 1 || 1 || 1 || 1 || 1 || 0 || 
|-
| 0 || 0 || 1 || 1 || 1 || 1 || 1 || 1 || 
|-
| 0 || 1 || 0 || 0 || 0 || 0 || 0 || 0 || Failed to initialize TF card || SD card not seated properly
|-
| 0 || 1 || 0 || 0 || 0 || 0 || 0 || 1 || 
|-
| 0 || 1 || 0 || 0 || 0 || 0 || 1 || 0 || 
|-
| 0 || 1 || 0 || 0 || 0 || 0 || 1 || 1 || 
|-
| 0 || 1 || 0 || 0 || 0 || 1 || 0 || 0 || Failed to read files in TF card || SD card not seated properly
|-
| 0 || 1 || 0 || 0 || 0 || 1 || 0 || 1 || 
|-
| 0 || 1 || 0 || 0 || 0 || 1 || 1 || 0 || 
|-
| 0 || 1 || 0 || 0 || 0 || 1 || 1 || 1 || 
|-
| 0 || 1 || 0 || 0 || 1 || 0 || 0 || 0 || Failed to open TF card || SD card not seated properly
|-
| 0 || 1 || 0 || 0 || 1 || 0 || 0 || 1 || 
|-
| 0 || 1 || 0 || 0 || 1 || 0 || 1 || 0 || 
|-
| 0 || 1 || 0 || 0 || 1 || 0 || 1 || 1 || 
|-
| 0 || 1 || 0 || 0 || 1 || 1 || 0 || 0 || Failed to write files to TF card || SD card not seated properly
|-
| 0 || 1 || 0 || 0 || 1 || 1 || 0 || 1 || 
|-
| 0 || 1 || 0 || 0 || 1 || 1 || 1 || 0 || 
|-
| 0 || 1 || 0 || 0 || 1 || 1 || 1 || 1 || 
|-
| 0 || 1 || 0 || 1 || 0 || 0 || 0 || 0 || 
|-
| 0 || 1 || 0 || 1 || 0 || 0 || 0 || 1 || 
|-
| 0 || 1 || 0 || 1 || 0 || 0 || 1 || 0 || 
|-
| 0 || 1 || 0 || 1 || 0 || 0 || 1 || 1 || 
|-
| 0 || 1 || 0 || 1 || 0 || 1 || 0 || 0 || 
|-
| 0 || 1 || 0 || 1 || 0 || 1 || 0 || 1 || 
|-
| 0 || 1 || 0 || 1 || 0 || 1 || 1 || 0 || 
|-
| 0 || 1 || 0 || 1 || 0 || 1 || 1 || 1 || 
|-
| 0 || 1 || 0 || 1 || 1 || 0 || 0 || 0 || 
|-
| 0 || 1 || 0 || 1 || 1 || 0 || 0 || 1 || 
|-
| 0 || 1 || 0 || 1 || 1 || 0 || 1 || 0 || 
|-
| 0 || 1 || 0 || 1 || 1 || 0 || 1 || 1 || 
|-
| 0 || 1 || 0 || 1 || 1 || 1 || 0 || 0 || 
|-
| 0 || 1 || 0 || 1 || 1 || 1 || 0 || 1 || 
|-
| 0 || 1 || 0 || 1 || 1 || 1 || 1 || 0 || 
|-
| 0 || 1 || 0 || 1 || 1 || 1 || 1 || 1 || 
|-
| 0 || 1 || 1 || 0 || 0 || 0 || 0 || 0 || 
|-
| 0 || 1 || 1 || 0 || 0 || 0 || 0 || 1 || 
|-
| 0 || 1 || 1 || 0 || 0 || 0 || 1 || 0 || 
|-
| 0 || 1 || 1 || 0 || 0 || 0 || 1 || 1 || 
|-
| 0 || 1 || 1 || 0 || 0 || 1 || 0 || 0 || 
|-
| 0 || 1 || 1 || 0 || 0 || 1 || 0 || 1 || 
|-
| 0 || 1 || 1 || 0 || 0 || 1 || 1 || 0 || 
|-
| 0 || 1 || 1 || 0 || 0 || 1 || 1 || 1 || 
|-
| 0 || 1 || 1 || 0 || 1 || 0 || 0 || 0 || 
|-
| 0 || 1 || 1 || 0 || 1 || 0 || 0 || 1 || 
|-
| 0 || 1 || 1 || 0 || 1 || 0 || 1 || 0 || 
|-
| 0 || 1 || 1 || 0 || 1 || 0 || 1 || 1 || 
|-
| 0 || 1 || 1 || 0 || 1 || 1 || 0 || 0 || 
|-
| 0 || 1 || 1 || 0 || 1 || 1 || 0 || 1 || 
|-
| 0 || 1 || 1 || 0 || 1 || 1 || 1 || 0 || 
|-
| 0 || 1 || 1 || 0 || 1 || 1 || 1 || 1 || 
|-
| 0 || 1 || 1 || 1 || 0 || 0 || 0 || 0 || 
|-
| 0 || 1 || 1 || 1 || 0 || 0 || 0 || 1 || 
|-
| 0 || 1 || 1 || 1 || 0 || 0 || 1 || 0 || 
|-
| 0 || 1 || 1 || 1 || 0 || 0 || 1 || 1 || 
|-
| 0 || 1 || 1 || 1 || 0 || 1 || 0 || 0 || 
|-
| 0 || 1 || 1 || 1 || 0 || 1 || 0 || 1 || 
|-
| 0 || 1 || 1 || 1 || 0 || 1 || 1 || 0 || 
|-
| 0 || 1 || 1 || 1 || 0 || 1 || 1 || 1 || 
|-
| 0 || 1 || 1 || 1 || 1 || 0 || 0 || 0 || 
|-
| 0 || 1 || 1 || 1 || 1 || 0 || 0 || 1 || 
|-
| 0 || 1 || 1 || 1 || 1 || 0 || 1 || 0 || 
|-
| 0 || 1 || 1 || 1 || 1 || 0 || 1 || 1 || 
|-
| 0 || 1 || 1 || 1 || 1 || 1 || 0 || 0 || 
|-
| 0 || 1 || 1 || 1 || 1 || 1 || 0 || 1 || 
|-
| 0 || 1 || 1 || 1 || 1 || 1 || 1 || 0 || 
|-
| 0 || 1 || 1 || 1 || 1 || 1 || 1 || 1 || 
|-
| 1 || 0 || 0 || 0 || 0 || 0 || 0 || 0 || 
|-
| 1 || 0 || 0 || 0 || 0 || 0 || 0 || 1 || 
|-
| 1 || 0 || 0 || 0 || 0 || 0 || 1 || 0 || 
|-
| 1 || 0 || 0 || 0 || 0 || 0 || 1 || 1 || 
|-
| 1 || 0 || 0 || 0 || 0 || 1 || 0 || 0 || Failed to initialize NOR in E3 || Check pads / clip at E3  board check may not be properly seated
|-
| 1 || 0 || 0 || 0 || 0 || 1 || 0 || 1 || Failed to read NOR in E3 || Check pads / clip at E3  board check may not be properly seated
|-
| 1 || 0 || 0 || 0 || 0 || 1 || 1 || 0 || Failed to erase NOR in E3 || Check pads / clip at E3  board check may not be properly seated
|-
| 1 || 0 || 0 || 0 || 0 || 1 || 1 || 1 || Failed to write NOR in E3 || Check pads / clip at E3  board check may not be properly seated
|-
| 1 || 0 || 0 || 0 || 1 || 0 || 0 || 0 || 
|-
| 1 || 0 || 0 || 0 || 1 || 0 || 0 || 1 || 
|-
| 1 || 0 || 0 || 0 || 1 || 0 || 1 || 0 || 
|-
| 1 || 0 || 0 || 0 || 1 || 0 || 1 || 1 || 
|-
| 1 || 0 || 0 || 0 || 1 || 1 || 0 || 0 || Failed to initialize PS3 BIOS || Check pads / clip at PS3 board check may not be properly seated
|-
| 1 || 0 || 0 || 0 || 1 || 1 || 0 || 1 || Failed to read PS3 BIOS || Check pads / clip at PS3 board check may not be properly seated
|-
| 1 || 0 || 0 || 0 || 1 || 1 || 1 || 0 || Failed to erase PS3 BIOS || Check pads / clip at PS3 board check may not be properly seated
|-
| 1 || 0 || 0 || 0 || 1 || 1 || 1 || 1 || Failed to write PS3 BIOS || Check pads / clip at PS3 board check may not be properly seated
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 0 || 0 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 0 || 1 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 1 || 0 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 1 || 1 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 0 || 0 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 0 || 1 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 1 || 0 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 1 || 1 || 
|-
| 1 || 0 || 0 || 1 || 0 || 1 || 0 || 0 || 
|-
| 1 || 0 || 0 || 1 || 0 || 1 || 0 || 1 || 
|-
| 1 || 0 || 0 || 1 || 0 || 1 || 1 || 0 || 
|-
| 1 || 0 || 0 || 1 || 0 || 1 || 1 || 1 || 
|-
| 1 || 0 || 0 || 1 || 1 || 0 || 0 || 0 || 
|-
| 1 || 0 || 0 || 1 || 1 || 0 || 0 || 1 || 
|-
| 1 || 0 || 0 || 1 || 1 || 0 || 1 || 0 || 
|-
| 1 || 0 || 0 || 1 || 1 || 0 || 1 || 1 || 
|-
| 1 || 0 || 0 || 1 || 1 || 1 || 0 || 0 || 
|-
| 1 || 0 || 0 || 1 || 1 || 1 || 0 || 1 || 
|-
| 1 || 0 || 0 || 1 || 1 || 1 || 1 || 0 || 
|-
| 1 || 0 || 0 || 1 || 1 || 1 || 1 || 1 || 
|-
| 1 || 0 || 1 || 0 || 0 || 0 || 0 || 0 || 
|-
| 1 || 0 || 1 || 0 || 0 || 0 || 0 || 1 || 
|-
| 1 || 0 || 1 || 0 || 0 || 0 || 1 || 0 || 
|-
| 1 || 0 || 1 || 0 || 0 || 0 || 1 || 1 || 
|-
| 1 || 0 || 1 || 0 || 0 || 1 || 0 || 0 || 
|-
| 1 || 0 || 1 || 0 || 0 || 1 || 0 || 1 || 
|-
| 1 || 0 || 1 || 0 || 0 || 1 || 1 || 0 || 
|-
| 1 || 0 || 1 || 0 || 0 || 1 || 1 || 1 || 
|-
| 1 || 0 || 1 || 0 || 1 || 0 || 0 || 0 || 
|-
| 1 || 0 || 1 || 0 || 1 || 0 || 0 || 1 || 
|-
| 1 || 0 || 1 || 0 || 1 || 0 || 1 || 0 || 
|-
| 1 || 0 || 1 || 0 || 1 || 0 || 1 || 1 || 
|-
| 1 || 0 || 1 || 0 || 1 || 1 || 0 || 0 || 
|-
| 1 || 0 || 1 || 0 || 1 || 1 || 0 || 1 || 
|-
| 1 || 0 || 1 || 0 || 1 || 1 || 1 || 0 || 
|-
| 1 || 0 || 1 || 0 || 1 || 1 || 1 || 1 || 
|-
| 1 || 0 || 1 || 1 || 0 || 0 || 0 || 0 || 
|-
| 1 || 0 || 1 || 1 || 0 || 0 || 0 || 1 || 
|-
| 1 || 0 || 1 || 1 || 0 || 0 || 1 || 0 || 
|-
| 1 || 0 || 1 || 1 || 0 || 0 || 1 || 1 || 
|-
| 1 || 0 || 1 || 1 || 0 || 1 || 0 || 0 || 
|-
| 1 || 0 || 1 || 1 || 0 || 1 || 0 || 1 || 
|-
| 1 || 0 || 1 || 1 || 0 || 1 || 1 || 0 || 
|-
| 1 || 0 || 1 || 1 || 0 || 1 || 1 || 1 || 
|-
| 1 || 0 || 1 || 1 || 1 || 0 || 0 || 0 || 
|-
| 1 || 0 || 1 || 1 || 1 || 0 || 0 || 1 || 
|-
| 1 || 0 || 1 || 1 || 1 || 0 || 1 || 0 || 
|-
| 1 || 0 || 1 || 1 || 1 || 0 || 1 || 1 || 
|-
| 1 || 0 || 1 || 1 || 1 || 1 || 0 || 0 || 
|-
| 1 || 0 || 1 || 1 || 1 || 1 || 0 || 1 || 
|-
| 1 || 0 || 1 || 1 || 1 || 1 || 1 || 0 || 
|-
| 1 || 0 || 1 || 1 || 1 || 1 || 1 || 1 || 
|-
| 1 || 1 || 0 || 0 || 0 || 0 || 0 || 0 || Wrong settings of switches || Check toggle switch - wrong setting
|-
| 1 || 1 || 0 || 0 || 0 || 0 || 0 || 1 || 
|-
| 1 || 1 || 0 || 0 || 0 || 0 || 1 || 0 || PS3 is operating NOR, E3 Flasher cannot operate at the same time || Check toggle switch - wrong setting
|-
| 1 || 1 || 0 || 0 || 0 || 0 || 1 || 1 || 
|-
| 1 || 1 || 0 || 0 || 0 || 1 || 0 || 0 || Not the right PS3 for this backup || Already used e3flasher on 1 console
|-
| 1 || 1 || 0 || 0 || 0 || 1 || 0 || 1 || 
|-
| 1 || 1 || 0 || 0 || 0 || 1 || 1 || 0 || 
|-
| 1 || 1 || 0 || 0 || 0 || 1 || 1 || 1 || 
|-
| 1 || 1 || 0 || 0 || 1 || 0 || 0 || 0 || Wrong PS3 version, not supported at present || Metldr.2 model undowngradable
|-
| 1 || 1 || 0 || 0 || 1 || 0 || 0 || 1 || 
|-
| 1 || 1 || 0 || 0 || 1 || 0 || 1 || 0 || 
|-
| 1 || 1 || 0 || 0 || 1 || 0 || 1 || 0 || 
|-
| 1 || 1 || 0 || 0 || 1 || 0 || 1 || 1 || 
|-
| 1 || 1 || 0 || 0 || 1 || 1 || 0 || 0 || Wrong function settings || Check toggle switch - wrong setting
|-
| 1 || 1 || 0 || 0 || 1 || 1 || 0 || 1 || 
|-
| 1 || 1 || 0 || 0 || 1 || 1 || 1 || 0 || 
|-
| 1 || 1 || 0 || 0 || 1 || 1 || 1 || 1 || 
|-
| 1 || 1 || 0 || 1 || 0 || 0 || 0 || 0 || 
|-
| 1 || 1 || 0 || 1 || 0 || 0 || 0 || 1 || 
|-
| 1 || 1 || 0 || 1 || 0 || 0 || 1 || 0 || 
|-
| 1 || 1 || 0 || 1 || 0 || 0 || 1 || 1 || 
|-
| 1 || 1 || 0 || 1 || 0 || 1 || 0 || 0 || 
|-
| 1 || 1 || 0 || 1 || 0 || 1 || 0 || 1 || 
|-
| 1 || 1 || 0 || 1 || 0 || 1 || 1 || 0 || 
|-
| 1 || 1 || 0 || 1 || 0 || 1 || 1 || 1 || 
|-
| 1 || 1 || 0 || 1 || 1 || 0 || 0 || 0 || 
|-
| 1 || 1 || 0 || 1 || 1 || 0 || 0 || 1 || 
|-
| 1 || 1 || 0 || 1 || 1 || 0 || 1 || 0 || 
|-
| 1 || 1 || 0 || 1 || 1 || 0 || 1 || 1 || 
|-
| 1 || 1 || 0 || 1 || 1 || 1 || 0 || 0 || 
|-
| 1 || 1 || 0 || 1 || 1 || 1 || 0 || 1 || 
|-
| 1 || 1 || 0 || 1 || 1 || 1 || 1 || 0 || 
|-
| 1 || 1 || 0 || 1 || 1 || 1 || 1 || 1 || 
|-
| 1 || 1 || 1 || 0 || 0 || 0 || 0 || 0 || 
|-
| 1 || 1 || 1 || 0 || 0 || 0 || 0 || 1 || 
|-
| 1 || 1 || 1 || 0 || 0 || 0 || 1 || 0 || 
|-
| 1 || 1 || 1 || 0 || 0 || 0 || 1 || 1 || 
|-
| 1 || 1 || 1 || 0 || 0 || 1 || 0 || 0 || 
|-
| 1 || 1 || 1 || 0 || 0 || 1 || 0 || 1 || 
|-
| 1 || 1 || 1 || 0 || 0 || 1 || 1 || 0 || 
|-
| 1 || 1 || 1 || 0 || 0 || 1 || 1 || 1 || 
|-
| 1 || 1 || 1 || 0 || 1 || 0 || 0 || 0 || 
|-
| 1 || 1 || 1 || 0 || 1 || 0 || 0 || 1 || 
|-
| 1 || 1 || 1 || 0 || 1 || 0 || 1 || 0 || 
|-
| 1 || 1 || 1 || 0 || 1 || 0 || 1 || 1 || 
|-
| 1 || 1 || 1 || 0 || 1 || 1 || 0 || 0 || 
|-
| 1 || 1 || 1 || 0 || 1 || 1 || 0 || 1 || 
|-
| 1 || 1 || 1 || 0 || 1 || 1 || 1 || 0 || 
|-
| 1 || 1 || 1 || 0 || 1 || 1 || 1 || 1 || 
|-
| 1 || 1 || 1 || 1 || 0 || 0 || 0 || 0 || 
|-
| 1 || 1 || 1 || 1 || 0 || 0 || 0 || 1 || 
|-
| 1 || 1 || 1 || 1 || 0 || 0 || 1 || 0 || 
|-
| 1 || 1 || 1 || 1 || 0 || 0 || 1 || 1 || 
|-
| 1 || 1 || 1 || 1 || 0 || 1 || 0 || 0 || 
|-
| 1 || 1 || 1 || 1 || 0 || 1 || 0 || 1 || 
|-
| 1 || 1 || 1 || 1 || 0 || 1 || 1 || 0 || 
|-
| 1 || 1 || 1 || 1 || 0 || 1 || 1 || 1 || 
|-
| 1 || 1 || 1 || 1 || 1 || 0 || 0 || 0 || 
|-
| 1 || 1 || 1 || 1 || 1 || 0 || 0 || 1 || 
|-
| 1 || 1 || 1 || 1 || 1 || 0 || 1 || 0 || 
|-
| 1 || 1 || 1 || 1 || 1 || 0 || 1 || 1 || 
|-
| 1 || 1 || 1 || 1 || 1 || 1 || 0 || 0 || 
|-
| 1 || 1 || 1 || 1 || 1 || 1 || 0 || 1 || 
|-
| 1 || 1 || 1 || 1 || 1 || 1 || 1 || 0 || 
|-
| 1 || 1 || 1 || 1 || 1 || 1 || 1 || 1 || 
|-
|}


=== Problem state 1 ===
* 10000100 - E3 can not initialize PS3 Nor Chip
* 10001100 - Error initializing the PS3 BIOS
* 10001101 - Error while reading PS3 BIOS
* 10001111 - Error writing PS3 BIOS 

Problem: bad solder points / E3 Nor Clip does not work right with Ps3 Nor 

<span style="text-decoration: underline;">'''solution''':</span> 
* check solder points (resolder) 
* Fat PS3 only: refit the Nor Clip by smoothing it down with a little screwdriver / sandpaper  
* clean contacts on Nor and E3 Clip with Isopropylalkohol 70% -
* use pads or cardboard to press down Nor clip                                                                                                                

[[File:E3.jpg]] 

'''Notes:''' 
* dont use to much pressure on the Nor because you will destroy the solder balls of your southbridge and damage your system .. 
* dont glue the inside of the clip to the nor chip 


=== Problem state 2 ===
* 10000101 - Reading error (E3 Nor)
* 10000111 - Error writing E3 Nor
* 10000110 - Error deleting data on E3 Nor
* 10001110 - Error erasing PS3 BIOS

Problem: faulty solder points / E3 Nor Clip does not work right with Ps3 Nor / E3 Nor bricked

<span style="text-decoration: underline;">'''solution''':</span> 
* check solder points 
* clean contacts on Nor and E3 Clip with Isopropylalkohol 70%
* use pads or cardboard to press down Nor Clip 
* reset E3 flasher while system is running (little red button on the upper side '''of the flasher''' / NOT little red button on front panel under Esata !!)

[[File:E3Platine.JPG]]

'''Notes:''' 
* dont use to much pressure on the Nor because you will destroy the solder balls of your southbridge and damage your system .. 
* dont glue the inside of the clip to the nor chip 

=== Problem state 3 ===
* 01000000 - Error initializing TF /SD card
* 01001000 - Error opening data from SD/TF card
* 01001100 - Error writing data from SD/TF card

<span style="text-decoration: underline;">'''solution''':</span> 
* check if TF/SD Card is sitting accurate 
* Format your SD/TF Card to FAT 32 
* Rename your backup '''bkpps3''' for writing to PS3 NOR / '''bkpe3''' for writing to E3 NOR 

=== Problem state 4 ===
* 11000000 - Wrong position of switches (the action you selected is not possible)
* 11001100 - Wrong position of switches (the action you selected is not possible)
* 11000010 - PS3 is using NOR / you cant use E3 Flasher at the same time

<span style="text-decoration: underline;">'''solution''':</span> 
* change position of switches

Note: On newer E3 versions there seems to be a high chance to get this error without any proper reason .. If you checked the position of switches and still get this error send your flasher in for replacement !!! As the error seems to appear quite often with the "new" models we tried a lot of ideas but nothing worked (cleaning faceplate contacts; using different faceplate; using different clip; soldering all wires to E3 Linker, adjusting pins ...)

=== Problem state 5 ===
* 11001000 - Wrong PS3 Version / Not supported PS3 Version (Nand / Metldr2)

<span style="text-decoration: underline;">'''Solution''':</span> 
* Buy a progskeet for nand :)

=== Problem state 6 ===
* 11000100 - corrupt backup of PS3 data

<span style="text-decoration: underline;">'''Solution''':</span> 
* check backup for errors (flowrebuilder etc) / make a new clean dump

=== Problem other frequent problems and solutions ===

====HDD in Esata Station cant be found====
* restrip contacts on the backside of the E3 Flasher (they must not touch the metal casing)
* they have to be isolated very good .. they are very sensitive and cause a lot of errors
* check Esata cable ..

====Blackscreen with no hdd activity and only hard reset possible (no brick)====
* resolder SBCE -> A / cut A/B properly
* restrip contacts on the backside of the E3 Flasher (they must not touch the metal casing) they have to be isolated very good .. they are very sensitive and cause a lot of errors
* if the E3 flasher is not connected, also ALWAYS disconnect the clip otherwise blackscreen because of A/B Cut .. 

In case your usb ports are still working:
* 3.55 ONLY: use the rsod/brickfix lv2diag in Service Mode (helped my system a lot .. it booted to blackscreen 8/10 times; after using lv2diag 2/10 times)
* if using TBv2 please note, that instead of proper security they used loops to protect their product; try reinstalling the FW via recovery mode
* also dont use custom boot logos with TBv2 !!
* Reinstall KMEAW based "no-check" MFW via recovery mode, as Kmeaw based LV2 seems to have better compatibility with the with Lv1 no-check patches(Thx Rogero!)

* if you have no success with the methods from above solder Tri/SBE and reflash a valid backup via flash fun mode (100000)

Note: I installed the E3 on a 3.55 Cfw Ps3 and took a backup (3.55 dump) .. Then i updated to 4.11 took another backup (4.11 dump) and bricked later .. Reflashing the clean 4.11 backup(which was made long before the brick)resulted in the same black screen again .. also flashing a patched 4.11 dump ended in blackscreen ..  
But flashing the 3.55 dump (after flashing the patched 4.11 backup) did the trick and fixed the black screen problem .. After reformating the HDD i was back on 3.55 even though i was on 4.11 before ..

====ylod behavior (3 beeps and turns off)====
There are two possible solutions .. Always try a) first then b)

:a) Dualboot only: 
::Wrong HDD in Esata Station<br />
::After downgrading your PS3 you have to install the <span style="text-decoration: underline;">SAME</span> firmware on <span style="text-decoration: underline;">BOTH</span> hdds then upgrade one HDD to OFW .. the error will be gone than .. <br />
::Example: downgrade to 3.55 kmeaw .. put 3.55 kmeaw on BOTH hdds via Recovery Mode .. then update your OFW HDD to 4.11 OFW .. 

:b)Brickfix: 
::well done .. you bricked your PS3 :)<br />
::Solder SBE to Tristate ..  use Flash Fun Mode (10000000) to reflash the valid back up of the firmware revision you bricked on .. 

====TrueBlue Dongle not working with dualboot (only red light)====
After downgrading your PS3 you have to install the <span style="text-decoration: underline;">SAME</span> firmware on <span style="text-decoration: underline;">BOTH</span> hdds then upgrade one HDD to OFW .. the error will be gone then .. 

Example: downgrade to 3.55 TBv2 no check .. install 3.55 TBv2 no check on BOTH hdds via Recovery Mode .. then update your OFW HDD to 4.11 OFW ..

'''NOTE: This has to be done EVERYTIME you update your OFW HDD to a higher firmware (for example also if you update from 4.11 to 4.20 !!!)'''

====No Blue Leds (only red power led)====
The Nor Clip is installed the wrong way .. you have to turn it 180° and reinstall it to the NOR .. 

The E3 flat cable has to lead away from the flasher NOT in the direction of the flasher ..

====Dualboot error: CFW HDD corrupted====
After updating your OFW HDD to a higher firmware your CFW HDD gets an error message and needs to be updated too  

'''<span style="text-decoration: underline;">Solution</span>''' 
* Resolder SBCE - A again; 
* Make sure the cut between A/B is deep enough 
* First solder then cut the connection between A/B !

====solder points (SBE / SBCE) torn off E3 ribbon cable====
solder points (SBE / SBCE) torn off E3 ribbon cable

'''<span style="text-decoration: underline;">Solution</span>''' 
* use alternate points on backside of E3 flasher 

[[File:Pinbelegungsdusbivehp.jpg]]


====IFI0 Tag missing at offset 200====
E3 finishes back up process without error, but Nor Patcher and Flowrebuilder finish with errors (bootloader 0kb/ IFI0 Tag missing at offset 200)


'''<span style="text-decoration: underline;">Solution</span>''' 
* Format SD Card again (Fat32)
* Reinstall and clean the contacts of the nor clip (not pressure issue but contact issue / dust etc.)
* clean linker to flatcable on E3 flasher
[[File:E3-Clip E3-Linker plug.jpg|300px]]
* if you still get this error you damaged the flatcable of your nor clip (Very easy to do !!)Replacement part needed ..

== E3 - Coverboard - switches ==
<div style="float:right">[[File:E3 - Coverboard - switches.jpg|200px|thumb|left|E3 - Coverboard - switches]]</div>
{| class="wikitable sortable"
|-
! Mode<br />flashfun (1)<br />ps3mode (0) !! Firmware<br />CFW (1)<br />OFW (0) !! Read/Write<br />Backup (1)<br />Program (0) !! Backup<br />OB Flash (1)<br />microSD (0) !! Program<br />OB Flash (1)<br />PS3Flash (0) !! Locking<br />Unlock (1)<br />Lock (0) !! Remarks
|-
| 0 || 0 || 0 || 0 || 0 || 0 || 
|-
| 0 || 0 || 0 || 0 || 0 || 1 || 
|-
| 0 || 0 || 0 || 0 || 1 || 0 || 
|-
| 0 || 0 || 0 || 0 || 1 || 1 || 
|-
| 0 || 0 || 0 || 1 || 0 || 0 || 
|-
| 0 || 0 || 0 || 1 || 0 || 1 || 
|-
| 0 || 0 || 0 || 1 || 1 || 0 || 
|-
| 0 || 0 || 0 || 1 || 1 || 1 || 
|-
| 0 || 0 || 1 || 0 || 0 || 0 || 
|-
| 0 || 0 || 1 || 0 || 0 || 1 || 
|-
| 0 || 0 || 1 || 0 || 1 || 0 || 
|-
| 0 || 0 || 1 || 0 || 1 || 1 || 
|-
| 0 || 0 || 1 || 1 || 0 || 0 || 
|-
| 0 || 0 || 1 || 1 || 0 || 1 || 
|-
| 0 || 0 || 1 || 1 || 1 || 0 || 
|-
| 0 || 0 || 1 || 1 || 1 || 1 || 
|-
| 0 || 1 || 0 || 0 || 0 || 0 || 
|-
| 0 || 1 || 0 || 0 || 0 || 1 || 
|-
| 0 || 1 || 0 || 0 || 1 || 0 || 
|-
| 0 || 1 || 0 || 0 || 1 || 1 || 
|-
| 0 || 1 || 0 || 1 || 0 || 0 || 
|-
| 0 || 1 || 0 || 1 || 0 || 1 || 
|-
| 0 || 1 || 0 || 1 || 1 || 0 || 
|-
| 0 || 1 || 0 || 1 || 1 || 1 || 
|-
| 0 || 1 || 1 || 0 || 0 || 0 || 
|-
| 0 || 1 || 1 || 0 || 0 || 1 || 
|-
| 0 || 1 || 1 || 0 || 1 || 0 || 
|-
| 0 || 1 || 1 || 0 || 1 || 1 || 
|-
| 0 || 1 || 1 || 1 || 0 || 0 || 
|-
| 0 || 1 || 1 || 1 || 0 || 1 || 
|-
| 0 || 1 || 1 || 1 || 1 || 0 || 
|-
| 0 || 1 || 1 || 1 || 1 || 1 || 
|-
| 1 || 0 || 0 || 0 || 0 || 0 || 
|-
| 1 || 0 || 0 || 0 || 0 || 1 || 
|-
| 1 || 0 || 0 || 0 || 1 || 0 || 
|-
| 1 || 0 || 0 || 0 || 1 || 1 || 
|-
| 1 || 0 || 0 || 1 || 0 || 0 || 
|-
| 1 || 0 || 0 || 1 || 0 || 1 || 
|-
| 1 || 0 || 0 || 1 || 1 || 0 || 
|-
| 1 || 0 || 0 || 1 || 1 || 1 || 
|-
| 1 || 0 || 1 || 0 || 0 || 0 || 
|-
| 1 || 0 || 1 || 0 || 0 || 1 || 
|-
| 1 || 0 || 1 || 0 || 1 || 0 || 
|-
| 1 || 0 || 1 || 0 || 1 || 1 || 
|-
| 1 || 0 || 1 || 1 || 0 || 0 || 
|-
| 1 || 0 || 1 || 1 || 0 || 1 || 
|-
| 1 || 0 || 1 || 1 || 1 || 0 || 
|-
| 1 || 0 || 1 || 1 || 1 || 1 || 
|-
| 1 || 1 || 0 || 0 || 0 || 0 || 
|-
| 1 || 1 || 0 || 0 || 0 || 1 || 
|-
| 1 || 1 || 0 || 0 || 1 || 0 || 
|-
| 1 || 1 || 0 || 0 || 1 || 1 || 
|-
| 1 || 1 || 0 || 1 || 0 || 0 || 
|-
| 1 || 1 || 0 || 1 || 0 || 1 || 
|-
| 1 || 1 || 0 || 1 || 1 || 0 || 
|-
| 1 || 1 || 0 || 1 || 1 || 1 || 
|-
| 1 || 1 || 1 || 0 || 0 || 0 || 
|-
| 1 || 1 || 1 || 0 || 0 || 1 || 
|-
| 1 || 1 || 1 || 0 || 1 || 0 || 
|-
| 1 || 1 || 1 || 0 || 1 || 1 || 
|-
| 1 || 1 || 1 || 1 || 0 || 0 || 
|-
| 1 || 1 || 1 || 1 || 0 || 1 || 
|-
| 1 || 1 || 1 || 1 || 1 || 0 || 
|-
| 1 || 1 || 1 || 1 || 1 || 1 || 
|-
|}

== Picture Gallery ==
<Gallery>
File:CLIP comparison.jpg| 360Clip and E3-Clip comparison 
File:CLIP styles.jpg| Clip Styles
File:E3 - Coverbard - working status.jpg| E3 - Coverbard - working status 
File:E3 - Panasonic PCB connector 50pin.jpg| E3 - Panasonic PCB connector 50pin
File:E3 Clip cable E3-Linkerboard Suit.jpg| E3 Clip cable E3-Linkerboard Suit
File:E3 Clip NOR Slim.jpg| E3 Clip NOR Slim
File:E3 flasher.jpg| E3-flasher
File:E3 flex cable SBE-SBCE.jpg| E3 flex cable SBE-SBCE
File:E3 Linker.jpg| E3-Linker
File:E3 on open DIA-002 to solve bad dumps.JPG| E3 on open DIA-002 to solve bad dumps
File:E3-Clip E3-Linker plug.jpg| E3-Clip E3-Linker plug
File:E3-Clip inside.jpg| E3-Clip inside
File:E3-Clip preparation.JPG| E3-Clip preparation
File:E3-Clip_Flexcable.JPG| E3 Clip - Flex Cable
File:E3-Clip_with_clamp_to_solve_bad_dumps.jpg| E3 Flasher - with clamp and coin to solve bad dumps
File:E3-Flasher on open MB PS3-SLIM.jpg| E3-Flasher - on open MB PS3-SLIM
File:E3-Flasher on open PS3-SLIM.jpg| E3-Flasher on open PS3-SLIM
File:E3-Flasher working on open PS3 DIA-002 with heatsink.JPG| E3 Flasher - on open PS3 DIA-002
File:E3-flasher-altern_sbe_sbce.jpg| E3 Flasher - Altern
File:E3-Flasher-chip-micro.jpg| E3-Flasher - ST ARM32 microcontroller
File:E3-Flasher-jtag.jpg| E3-Flasher - jtag
File:E3-img0002dcz.jpg| E3 Flasher - BACK
File:E3-img0004xv.jpg| E3 Flasher - TOP
</Gallery>

== External references ==
warning: maybe severly incomplete (always use <span style="text-decoration: underline;">alongside</span> this wiki main reference pages) :

* [http://www.ps3-infos.fr/forum/tutoriaux-f44/controle-des-dump-debrickage-classique-et-alternatif-t2976.html Partial validation of dumps (French)]
* [http://www.ps3-infos.fr/forum/tutoriaux-f44/remplacement-clip-e3flasher-par-le-e3linker-complement-au-tuto-e3flasher-t2865.html E3 linker installation (French)]
* [http://www.ps3-infos.fr/forum/tutoriaux-f44/e3-flasher-install-downgrade-ps3-config-half-et-fast-dual-boot-t2649.html E3 Installation (French)]
* [http://www.ps3-addict.fr/forum/debrikage-ps3-ylodee-par-flasher-fixed-t5092.html Debricking with E3 (French)]