MechaCon/UART commands
Jump to navigation
Jump to search
Overview
These commands can be sent to MechaCon via it's UART interface. They exist for manufacturing and servicing purposes. For wiring up a serial terminal to the MechaCon UART interface, see MechaCon UART test points. To enable the UART interface, the console must be put in testmode by pulling the RMC test point to ground.
Instead of working with raw MechaCon commands, it is recommended for users to use pre-made tools like PMAP. The purpose of this page is to provide documentation for the further development of PS2 tools.
Commands
| Command | Description | Parameters | Return values | Remarks |
|---|---|---|---|---|
| 0xc00 | MECHA_CMD_INIT_SHIMUKE | |||
| 0xc01 | MECHA_CMD_INIT_MECHACON | |||
| 0xc10 | MECHA_CMD_DISC_MODE_CD_8 | |||
| 0xc11 | MECHA_CMD_DISC_MODE_CD_12 | |||
| 0xc12 | MECHA_CMD_DISC_MODE_DVDSL_8 | |||
| 0xc13 | MECHA_CMD_DISC_MODE_DVDDL_8 | |||
| 0xc14 | MECHA_CMD_DISC_MODE_DVDSL_12 | |||
| 0xc15 | MECHA_CMD_DISC_MODE_DVDDL_12 | |||
| 0xc16 | MECHA_CMD_DISC_DETECT | |||
| 0xc20 | MECHA_CMD_LASER_DIODE | |||
| 0xc22 | MECHA_CMD_FOCUS_UPDOWN | |||
| 0xc23 | MECHA_CMD_FOCUS_AUTO_START | |||
| 0xc24 | MECHA_CMD_FOCUS_AUTO_STOP | |||
| 0xc25 | MECHA_CMD_FCS_SEARCH_CHECK | |||
| 0xc30 | MECHA_CMD_TRACKING | |||
| 0xc41 | MECHA_CMD_SLED_CTL_MICRO | |||
| 0xc42 | MECHA_CMD_SLED_CTL_BIPHS | |||
| 0xc43 | MECHA_CMD_SLED_CTL_POS | |||
| 0xc44 | MECHA_CMD_SLED_POS_HOME | |||
| 0xc45 | MECHA_CMD_SLED_IN_SW | |||
| 0xc50 | MECHA_CMD_SP_CTL | |||
| 0xc51 | MECHA_CMD_SP_CLV_S | |||
| 0xc52 | MECHA_CMD_SP_CLV_A | |||
| 0xc60 | MECHA_CMD_TRAY | |||
| 0xc61 | MECHA_CMD_TRAY_SW | |||
| 0xc8d | MECHA_CMD_CLEAR_CONF | |||
| 0xc8e | MECHA_CMD_UPLOAD_NEW | 00 | ||
| 0xc93 | MECHA_CMD_UPLOAD_TO_RAM | |||
| 0xc97 | MECHA_CMD_DETECT_ADJ | |||
| 0xc99 | MECHA_CMD_WRITE_CHECKSUM | |||
| 0xc9a | MECHA_CMD_READ_CHECKSUM | |||
| 0xc9b | MECHA_CMD_SETUP_OSD | 00 = NTSC, 01 = PAL, presumed to be supported by DEX B and later. | ||
| 0xc9e | MECHA_CMD_SETUP_SANYO | |||
| 0xca1 | MECHA_CMD_AUTO_ADJ_ST_1 | |||
| 0xca2 | MECHA_CMD_AUTO_ADJ_ST_2 | |||
| 0xca3 | MECHA_CMD_AUTO_ADJ_ST_12 | |||
| 0xca4 | MECHA_CMD_AUTO_ADJ_ST_2MD | Performed during skew adjustment initialization. | ||
| 0xca5 | MECHA_CMD_AUTO_ADJ_FIX_GAIN | |||
| 0xca7 | MECHA_CMD_RFDC_LEVEL | |||
| 0xca8 | MECHA_CMD_TPP | |||
| 0xcaa | MECHA_CMD_MIRR_CHECK | |||
| 0xcab | MECHA_CMD_FE_OFFSET | |||
| 0xcb0 | MECHA_CMD_CD_PLAY_1 | 1x | ||
| 0xcb1 | MECHA_CMD_CD_PLAY_2 | 2x | ||
| 0xcb2 | MECHA_CMD_CD_PLAY_3 | 4x | ||
| 0xcb3 | MECHA_CMD_CD_PLAY_4 | 5-12x | ||
| 0xcb4 | MECHA_CMD_CD_STOP | |||
| 0xcb5 | MECHA_CMD_CD_PAUSE | |||
| 0xcb6 | MECHA_CMD_CD_TRACK_CTL | |||
| 0xcb8 | MECHA_CMD_CD_TRACK_LONG_CTL | |||
| 0xcb9 | MECHA_CMD_CD_PLAY_5 | 10-24x | ||
| 0xcc0 | MECHA_CMD_DVD_PLAY_1 | 1x | ||
| 0xcc1 | MECHA_CMD_DVD_PLAY_2 | 1.6x | ||
| 0xcc2 | MECHA_CMD_DVD_PLAY_3 | 1.6-4x | ||
| 0xcc3 | MECHA_CMD_DVD_STOP | |||
| 0xcc4 | MECHA_CMD_DVD_PAUSE | |||
| 0xcc5 | MECHA_CMD_DVD_TRACK_CTL | |||
| 0xcc7 | MECHA_CMD_DVD_TRACK_LONG_CTL | |||
| 0xcc8 | MECHA_CMD_FOCUS_JUMP | |||
| 0xcca | MECHA_CMD_ADJ_AUTO_TILT | |||
| 0xccb | MECHA_CMD_INIT_AUTO_TILT | |||
| 0xccd | MECHA_CMD_MOV_AUTO_TILT | |||
| 0xcd1 | MECHA_CMD_SET_DSP | |||
| 0xcd3 | MECHA_CMD_GAIN | |||
| 0xcde | MECHA_CMD_DSP_ERROR_RATE_CTL | |||
| 0xcdf | MECHA_CMD_DSP_ERROR_RATE | |||
| 0xce0 | MECHA_CMD_EEPROM_WRITE | aaaadddd | ce0aaaadddd a = address, d = data. | |
| 0xce1 | MECHA_CMD_EEPROM_READ | aaaa | ce1aaaa a = address | |
| 0xce4 | MECHA_CMD_RTC_READ | |||
| 0xce5 | MECHA_CMD_RTC_WRITE | |||
| 0xce6 | MECHA_CMD_ECR_READ | |||
| 0xce7 | MECHA_CMD_ECR_WRITE | |||
| 0xce8 | MECHA_CMD_CD_ERROR | |||
| 0xce9 | MECHA_CMD_JITTER | |||
| 0xcf2 | MECHA_CMD_FOCUS_JUMP_NEW | |||
| 0xcfa | MECHA_CMD_CFA | |||
| 0xcfc | MECHA_CMD_READ_MODEL_2 | |||
| 0xcfd | MECHA_CMD_READ_MODEL | |||
| 0xcfe | MECHA_CMD_EEPROM_ERASE |