MechaCon/UART commands/SPC970: Difference between revisions
Jump to navigation
Jump to search
| (4 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
See [[MechaCon]] and [[MechaCon/UART commands]] for basic information. | See [[MechaCon]] and [[MechaCon/UART commands]] for basic information. | ||
= Command list = | = Command list = | ||
'''Note: This is subject to ongoing research and partially inaccurate''' | '''Note: This is subject to ongoing research and partially inaccurate'''<br/> | ||
'''All communication uses ASCII-encoded Hex-values.''' | |||
''Not all of these commands are available on every MechaCon version'' | ''Not all of these commands are available on every MechaCon version'' | ||
| Line 65: | Line 66: | ||
| 0xc93 || MECHA_CMD_UPLOAD_TO_RAM || || || | | 0xc93 || MECHA_CMD_UPLOAD_TO_RAM || || || | ||
|- | |- | ||
| 0xc97 || MECHA_CMD_DETECT_ADJ || || || | | 0xc97 || MECHA_CMD_DETECT_ADJ || || || | ||
|- | |- | ||
| 0xc99 || MECHA_CMD_WRITE_CHECKSUM || || || | | 0xc99 || MECHA_CMD_WRITE_CHECKSUM || || || | ||
| Line 161: | Line 162: | ||
| 0xcfc || MECHA_CMD_READ_MODEL_2 || || || | | 0xcfc || MECHA_CMD_READ_MODEL_2 || || || | ||
|- | |- | ||
| 0xcfd || MECHA_CMD_READ_MODEL || || | | 0xcfd || MECHA_CMD_READ_MODEL || || vvvvrr (v = [[MechaCon#Firmware_revisions|version]], r = [[MechaCon#Bits|region]]) || | ||
|- | |- | ||
| 0xcfe || MECHA_CMD_EEPROM_ERASE || || || | | 0xcfe || MECHA_CMD_EEPROM_ERASE || || || | ||
| Line 179: | Line 180: | ||
| 0x2A0 || Rx-command error | | 0x2A0 || Rx-command error | ||
|- | |- | ||
| 0x2A1 || Rx-command argument count error | | 0x2A1 || Rx-command invalid argument count error | ||
|- | |- | ||
| 0x2A2 || Rx-command argument | | 0x2A2 || Rx-command invalid argument error | ||
|- | |- | ||
|} | |} | ||
Latest revision as of 00:16, 19 October 2024
Overview[edit | edit source]
See MechaCon and MechaCon/UART commands for basic information.
Command list[edit | edit source]
Note: This is subject to ongoing research and partially inaccurate
All communication uses ASCII-encoded Hex-values.
Not all of these commands are available on every MechaCon version
| Command | Description | Parameters | Return values | Usage/Remarks |
|---|---|---|---|---|
| 0xc00 | MECHA_CMD_INIT_SHIMUKE | |||
| 0xc01 | MECHA_CMD_INIT_MECHACON | |||
| 0xc10 | MECHA_CMD_DISC_MODE_CD_8 | |||
| 0xc11 | MECHA_CMD_DISC_MODE_CD_12 | |||
| 0xc12 | MECHA_CMD_DISC_MODE_DVDSL_8 | |||
| 0xc13 | MECHA_CMD_DISC_MODE_DVDDL_8 | |||
| 0xc14 | MECHA_CMD_DISC_MODE_DVDSL_12 | |||
| 0xc15 | MECHA_CMD_DISC_MODE_DVDDL_12 | |||
| 0xc16 | MECHA_CMD_DISC_DETECT | |||
| 0xc20 | MECHA_CMD_LASER_DIODE | |||
| 0xc22 | MECHA_CMD_FOCUS_UPDOWN | |||
| 0xc23 | MECHA_CMD_FOCUS_AUTO_START | |||
| 0xc24 | MECHA_CMD_FOCUS_AUTO_STOP | |||
| 0xc25 | MECHA_CMD_FCS_SEARCH_CHECK | |||
| 0xc30 | MECHA_CMD_TRACKING | |||
| 0xc41 | MECHA_CMD_SLED_CTL_MICRO | |||
| 0xc42 | MECHA_CMD_SLED_CTL_BIPHS | |||
| 0xc43 | MECHA_CMD_SLED_CTL_POS | |||
| 0xc44 | MECHA_CMD_SLED_POS_HOME | |||
| 0xc45 | MECHA_CMD_SLED_IN_SW | |||
| 0xc50 | MECHA_CMD_SP_CTL | |||
| 0xc51 | MECHA_CMD_SP_CLV_S | |||
| 0xc52 | MECHA_CMD_SP_CLV_A | |||
| 0xc60 | MECHA_CMD_TRAY | |||
| 0xc61 | MECHA_CMD_TRAY_SW | |||
| 0xc8d | MECHA_CMD_CLEAR_CONF | |||
| 0xc8e | MECHA_CMD_UPLOAD_NEW | 00 | ||
| 0xc93 | MECHA_CMD_UPLOAD_TO_RAM | |||
| 0xc97 | MECHA_CMD_DETECT_ADJ | |||
| 0xc99 | MECHA_CMD_WRITE_CHECKSUM | |||
| 0xc9a | MECHA_CMD_READ_CHECKSUM | |||
| 0xc9b | MECHA_CMD_SETUP_OSD | 00 = NTSC, 01 = PAL, presumed to be supported by DEX B and later | ||
| 0xc9e | MECHA_CMD_SETUP_SANYO | |||
| 0xca1 | MECHA_CMD_AUTO_ADJ_ST_1 | |||
| 0xca2 | MECHA_CMD_AUTO_ADJ_ST_2 | |||
| 0xca3 | MECHA_CMD_AUTO_ADJ_ST_12 | |||
| 0xca4 | MECHA_CMD_AUTO_ADJ_ST_2MD | Performed during skew adjustment initialization | ||
| 0xca5 | MECHA_CMD_AUTO_ADJ_FIX_GAIN | |||
| 0xca7 | MECHA_CMD_RFDC_LEVEL | |||
| 0xca8 | MECHA_CMD_TPP | |||
| 0xcaa | MECHA_CMD_MIRR_CHECK | |||
| 0xcab | MECHA_CMD_FE_OFFSET | |||
| 0xcb0 | MECHA_CMD_CD_PLAY_1 | 1x CLV | ||
| 0xcb1 | MECHA_CMD_CD_PLAY_2 | 2x CLV | ||
| 0xcb2 | MECHA_CMD_CD_PLAY_3 | 4x CLV | ||
| 0xcb3 | MECHA_CMD_CD_PLAY_4 | 5-12x CAV | ||
| 0xcb4 | MECHA_CMD_CD_STOP | |||
| 0xcb5 | MECHA_CMD_CD_PAUSE | |||
| 0xcb6 | MECHA_CMD_CD_TRACK_CTL | |||
| 0xcb8 | MECHA_CMD_CD_TRACK_LONG_CTL | |||
| 0xcb9 | MECHA_CMD_CD_PLAY_5 | 10-24x CAV | ||
| 0xcc0 | MECHA_CMD_DVD_PLAY_1 | 1x CLV | ||
| 0xcc1 | MECHA_CMD_DVD_PLAY_2 | 1.6x CLV | ||
| 0xcc2 | MECHA_CMD_DVD_PLAY_3 | 1.6-4x CAV | ||
| 0xcc3 | MECHA_CMD_DVD_STOP | |||
| 0xcc4 | MECHA_CMD_DVD_PAUSE | |||
| 0xcc5 | MECHA_CMD_DVD_TRACK_CTL | |||
| 0xcc7 | MECHA_CMD_DVD_TRACK_LONG_CTL | |||
| 0xcc8 | MECHA_CMD_FOCUS_JUMP | |||
| 0xcca | MECHA_CMD_ADJ_AUTO_TILT | |||
| 0xccb | MECHA_CMD_INIT_AUTO_TILT | |||
| 0xccd | MECHA_CMD_MOV_AUTO_TILT | |||
| 0xcd1 | MECHA_CMD_SET_DSP | |||
| 0xcd3 | MECHA_CMD_GAIN | |||
| 0xcde | MECHA_CMD_DSP_ERROR_RATE_CTL | |||
| 0xcdf | MECHA_CMD_DSP_ERROR_RATE | |||
| 0xce0 | MECHA_CMD_EEPROM_WRITE | aaaadddd | 0aaaadddd (returns written data, not previous data) | ce0aaaadddd (a = address, d = data) |
| 0xce1 | MECHA_CMD_EEPROM_READ | aaaa | 0aaaadddd | ce1aaaa (a = address) |
| 0xce4 | MECHA_CMD_RTC_READ | |||
| 0xce5 | MECHA_CMD_RTC_WRITE | |||
| 0xce6 | MECHA_CMD_ECR_READ | |||
| 0xce7 | MECHA_CMD_ECR_WRITE | |||
| 0xce8 | MECHA_CMD_CD_ERROR | |||
| 0xce9 | MECHA_CMD_JITTER | |||
| 0xcf2 | MECHA_CMD_FOCUS_JUMP_NEW | |||
| 0xcfc | MECHA_CMD_READ_MODEL_2 | |||
| 0xcfd | MECHA_CMD_READ_MODEL | vvvvrr (v = version, r = region) | ||
| 0xcfe | MECHA_CMD_EEPROM_ERASE |
Command documentation[edit | edit source]
To do: document more complex commands here
Error codes[edit | edit source]
| Code | Description |
|---|---|
| 0x2A0 | Rx-command error |
| 0x2A1 | Rx-command invalid argument count error |
| 0x2A2 | Rx-command invalid argument error |