Editing Test points/MechaCon UART
Jump to navigation
Jump to search
The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 6: | Line 6: | ||
The publicly available service tools only support consoles up to the G-chassis (up to including SCPH-37000 and SCPH-39000 series).<br/> | The publicly available service tools only support consoles up to the G-chassis (up to including SCPH-37000 and SCPH-39000 series).<br/> | ||
PMAP additionally | PMAP additionally supports H and I chassis consoles (most SCPH-50000 series consoles). | ||
Currently missing (please contribute): | Currently missing (please contribute): | ||
* GH-008, GH-016, GH-017, GH-029 | * GH-008, GH-016, GH-017, GH-018, GH-026, GH-029, GH-032, GH-036, GH-040, GH-041, GH-061 (some sub-revisions), GH-062 | ||
=Notes= | |||
*'''RX''' and '''TX''' are sometimes swapped in these pictures. This is due to the contributors not having unified their naming conventions, with some marking RX and TX as seen from the MechaCon's side and others marking RX and TX as seen from the PC's (or it's interface's) side. If you can't establish a connection one way, you should try swapping RX and TX and try again. There are plans for unifying the naming in the future. | *'''RX''' and '''TX''' are sometimes swapped in these pictures. This is due to the contributors not having unified their naming conventions, with some marking RX and TX as seen from the MechaCon's side and others marking RX and TX as seen from the PC's (or it's interface's) side. If you can't establish a connection one way, you should try swapping RX and TX and try again. There are plans for unifying the naming in the future. | ||
*The '''3.3V''' marked on most pictures are '''actually 3.5V''', since that's what MechaCon runs off. If you are using e.g. a RS232-to-TTL level shifter (like e.g. a MAX3232-based level shifter), the PS2's 3.5V need to be connected to your level shifter's Vcc. However, it should not be connected to anything that has it's own 3.3V regulator (like e.g. some USB-to-TTL converters), since the regulator on the PS2's board and your converter will end up in a feedback loop, potentially causing damage. There are plans for unifying the naming in the future. | *The '''3.3V''' marked on most pictures are '''actually 3.5V''', since that's what MechaCon runs off. If you are using e.g. a RS232-to-TTL level shifter (like e.g. a MAX3232-based level shifter), the PS2's 3.5V need to be connected to your level shifter's Vcc. However, it should not be connected to anything that has it's own 3.3V regulator (like e.g. some USB-to-TTL converters), since the regulator on the PS2's board and your converter will end up in a feedback loop, potentially causing damage. There are plans for unifying the naming in the future. | ||
| Line 68: | Line 63: | ||
===GH-018=== | ===GH-018=== | ||
===GH-019=== | ===GH-019=== | ||
| Line 82: | Line 76: | ||
===GH-026=== | ===GH-026=== | ||
===GH-029=== | ===GH-029=== | ||
| Line 91: | Line 84: | ||
===GH-032=== | ===GH-032=== | ||
[[File:GH-032 Mechacon UART.jpg|left|thumb|201x201px]] | |||
[[File:GH-032 Mechacon UART.jpg| | |||
===GH-035=== | ===GH-035=== | ||
[[File:GH-035 test points.png|200px]] | [[File:GH-035 test points.png|200px]] | ||
===GH-036=== | ===GH-036=== | ||
===GH-037=== | ===GH-037=== | ||
| Line 106: | Line 95: | ||
==GH-04X== | ==GH-04X== | ||
===GH-040=== | ===GH-040=== | ||
===GH-041=== | ===GH-041=== | ||
==GH-05X== | ==GH-05X== | ||
| Line 122: | Line 110: | ||
==GH-06X== | ==GH-06X== | ||
===GH-061 | ===GH-061=== | ||
''On the top side, next to the Ethernet connector | '''For GH-061-22 and GH-061-42:''' ''On the top side, next to the Ethernet connector''<br/> | ||
[[File:Slim79.png|200px]] | [[File:Slim79.png|200px]] | ||
''For GH-061-12 | '''For GH-061-12 and GH-061-51: unknown''' | ||
' | |||
===GH-062=== | ===GH-062=== | ||
==GH-07X== | ==GH-07X== | ||