Editing Test points/MechaCon UART

These are the test points exposing [[MechaCon]]'s UART interface e.g. for [[CDVD Drive]] calibration using PMAP. These test points have also been used by Sony service centers via official service tools.

To put the console into service mode, the RMC/test mode test point needs to be grounded. This is necessary when recalibrating the drive and doing other stuff.

Depending on how you connect to the console, you might have to swap RX and TX with each other.

The publicly available service tools only support consoles up to the G-chassis (up to including SCPH-37000 and SCPH-39000 series).<br/>
PMAP additionally supports H and I chassis consoles (most SCPH-50000 series consoles).

Currently missing (please contribute):
* GH-008, GH-016, GH-017, GH-018, GH-029, GH-036, GH-040, GH-041, GH-061 (some sub-revisions), GH-062

=How to connect=
To enable the UART interface, the console must be put into testmode by pulling the TEST_MODE0 test point to ground. The interface operates at '''57600 baud 8N1''' (automatically set correctly by PMAP and the official service tools) and rather non-standard '''3.5&nbsp;V'''. 

3.3&nbsp;V signal levels work fine for communication, but care must be taken not to additionally connect an internal 3V3 voltage regulator, which is provided on some USB UART interfaces, to the console, since this will conflict with the console's own 3V5 voltage regulation and could damage the USB device and/or the console. On such interfaces, it should suffice to '''just connect Rx, Tx and GND'''. Even better would be to use a RS-232-to-TTL level shifter, which can take the 3V5 voltage as reference directly from the console itself.

==Notes==
*'''RX''' and '''TX''' are sometimes swapped in these pictures. This is due to the contributors not having unified their naming conventions, with some marking RX and TX as seen from the MechaCon's side and others marking RX and TX as seen from the PC's (or it's interface's) side. If you can't establish a connection one way, you should try swapping RX and TX and try again. There are plans for unifying the naming in the future.
*The '''3.3V''' marked on most pictures are '''actually 3.5V''', since that's what MechaCon runs off. If you are using e.g. a RS232-to-TTL level shifter (like e.g. a MAX3232-based level shifter), the PS2's 3.5V need to be connected to your level shifter's Vcc. However, it should not be connected to anything that has it's own 3.3V regulator (like e.g. some USB-to-TTL converters), since the regulator on the PS2's board and your converter will end up in a feedback loop, potentially causing damage. There are plans for unifying the naming in the future.
*'''RMC''' is actually named '''TEST_MODE0'''. This mistake comes from the fact that the generic microcontroller that the SPC970-MechaCon is based on has an alternate function on the same pin called RMC ('''R'''e'''M'''ote'''C'''ontroller), which is an internal remote control signal decoder. This alternate function is unused on PS2 and does not exist on the Dragon-MechaCon. There are plans for unifying the naming in the future.

=Playstation 2 Fat Motherboard Models=

==GH-00X==

===GH-001===
[[File:S43vRdP.jpg|200px]]

===GH-003===
''Identical to GH-001''<br/>
[[File:RDPT7ax.jpg|200px]]

===GH-004===
''Identical to GH-005''<br/>

===GH-005===
[[File:6jokfw1.jpg|200px]]

===GH-006===
[[File:vOfzfpA.jpg|200px]]

===GH-007===
''Identical to GH-006''<br/>

===GH-008===

==GH-01X==

===GH-010===
[[File:e2cm6MO.jpg|200px]]

===GH-012===
''Identical to GH-010''<br/>

===GH-013===
''Identical to GH-010''<br/>

===GH-014===
''Identical to GH-010''<br/>

===GH-015===
[[File:3noGpdf.jpg|200px]]

===GH-016===

===GH-017===

===GH-018===

===GH-019===
[[File:3BN1Nib.jpg|200px]]

==GH-02X==

===GH-022===
''Identical to GH-019''<br/>

===GH-023===
[[File:3XVAvq3.jpg|200px]]

===GH-026===
[[File:GH-026 Mechacon UART.jpg|200px]]

===GH-029===

=Playstation 2 Slim Motherboard Models=

==GH-03X==

===GH-032===
''Identical to GH-035''</br>
[[File:GH-032 Mechacon UART.jpg|200px]]

===GH-035===
''Identical to GH-032''</br>
[[File:GH-035 test points.png|200px]]

===GH-036===
[[File:GH-036 UART Test Points.jpg|200px]]
''Please contribute a good 3.5V test point''

===GH-037===
[[File:GH-037 test points.jpg|200px]]

==GH-04X==

===GH-040===

===GH-041===

==GH-05X==

===GH-051===
[[File:GH-051 MechaCon UART.png|200px]]

===GH-052===
[[File:GH-052 UART.jpg|frameless]]

==GH-06X==

===GH-061===
'''For GH-061-22 and GH-061-42:''' ''On the top side, next to the Ethernet connector''<br/>
[[File:Slim79.png|200px]]

''For GH-061-12, TX, RX, RMC, and Ground are the same as GH-061-22. 3.3 V/3.5 V point shown in that diagram might not supply enough amperage to power a USB-UART device requiring external power, so use an alternate 3.3v point such as the one recommended for installing Modbo.'' 



'''''For GH-061-51:''''' ''On the top side of the board, two points being above and one point being to the left of the MechaCon.''<br/>
[[File:PS2 SLim GH-061-51 UART Points.jpg|200px]]

===GH-062===
''GH-062-02, located near the top left corner of the MechaCon.''<br/>
[[File:GH-62-02 Solder Points for Test Mode.jpg|200px]]

==GH-07X==

===GH-070===
''On the top side, next to the Ethernet connector''<br/>
[[File:Test points GH-070-71-72.png|200px]]

===GH-071===
''Identical to GH-070''<br/>

===GH-072===
''Identical to GH-070''<br/>

=PSX Motherboard Models=

===XPD-001===
''Identical to XPD-005''<br/>

===XPD-005===
[[File:Hz1QY2W.jpg|200px]]