Editing Test points/MechaCon UART

These are the test points exposing [[MechaCon]]'s UART interface e.g. for [[CDVD Drive]] calibration using PMAP. These test points have also been used by Sony service centers via official service tools.

To put the console into service mode, the RMC/test mode test point needs to be grounded. This is necessary when recalibrating the drive and doing other stuff.

Depending on how you connect to the console, you might have to swap RX and TX with each other.

The publicly available service tools only support consoles up to the G-chassis (up to including SCPH-37000 and SCPH-39000 series).<br/>
PMAP additionally supports H and I chassis consoles (most SCPH-50000 series consoles).

Currently missing (please contribute):
* GH-008, GH-016, GH-017, GH-018, GH-026, GH-029, GH-032, GH-036, GH-040, GH-041, GH-061 (some sub-revisions), GH-062

=Notes=
*'''RX''' and '''TX''' are sometimes swapped in these pictures. This is due to the contributors not having unified their naming conventions, with some marking RX and TX as seen from the MechaCon's side and others marking RX and TX as seen from the PC's (or it's interface's) side. If you can't establish a connection one way, you should try swapping RX and TX and try again. There are plans for unifying the naming in the future.
*The '''3.3V''' marked on most pictures are '''actually 3.5V''', since that's what MechaCon runs off. If you are using e.g. a RS232-to-TTL level shifter (like e.g. a MAX3232-based level shifter), the PS2's 3.5V need to be connected to your level shifter's Vcc. However, it should not be connected to anything that has it's own 3.3V regulator (like e.g. some USB-to-TTL converters), since the regulator on the PS2's board and your converter will end up in a feedback loop, potentially causing damage. There are plans for unifying the naming in the future.
*'''RMC''' is actually named '''TEST_MODE0'''. This mistake comes from the fact that the generic microcontroller that the SPC970-MechaCon is based on has an alternate function on the same pin called RMC ('''R'''e'''M'''ote'''C'''ontroller), which is an internal remote control signal decoder. This alternate function is unused on PS2 and does not exist on the Dragon-MechaCon. There are plans for unifying the naming in the future.

=Playstation 2 Fat Motherboard Models=

==GH-00X==

===GH-001===
[[File:S43vRdP.jpg|200px]]

===GH-003===
''Identical to GH-001''<br/>
[[File:RDPT7ax.jpg|200px]]

===GH-004===
''Identical to GH-005''<br/>

===GH-005===
[[File:6jokfw1.jpg|200px]]

===GH-006===
[[File:vOfzfpA.jpg|200px]]

===GH-007===
''Identical to GH-006''<br/>

===GH-008===

==GH-01X==

===GH-010===
[[File:e2cm6MO.jpg|200px]]

===GH-012===
''Identical to GH-010''<br/>

===GH-013===
''Identical to GH-010''<br/>

===GH-014===
''Identical to GH-010''<br/>

===GH-015===
[[File:3noGpdf.jpg|200px]]

===GH-016===

===GH-017===

===GH-018===

===GH-019===
[[File:3BN1Nib.jpg|200px]]

==GH-02X==

===GH-022===
''Identical to GH-019''<br/>

===GH-023===
[[File:3XVAvq3.jpg|200px]]

===GH-026===

===GH-029===

=Playstation 2 Slim Motherboard Models=

==GH-03X==

===GH-032===
''Identical to GH-035''</br>
[[File:GH-032 Mechacon UART.jpg|200px]]

===GH-035===
''Identical to GH-032''</br>
[[File:GH-035 test points.png|200px]]

===GH-036===

===GH-037===
[[File:GH-037 test points.jpg|200px]]

==GH-04X==

===GH-040===

===GH-041===

==GH-05X==

===GH-051===
[[File:GH-051 MechaCon UART.png|200px]]

===GH-052===
[[File:GH-052 UART.jpg|frameless]]

==GH-06X==

===GH-061===
'''For GH-061-22 and GH-061-42:''' ''On the top side, next to the Ethernet connector''<br/>
[[File:Slim79.png|200px]]

'''For GH-061-12 and GH-061-51: unknown'''

===GH-062===

==GH-07X==

===GH-070===
''On the top side, next to the Ethernet connector''<br/>
[[File:Test points GH-070-71-72.png|200px]]

===GH-071===
''Identical to GH-070''<br/>

===GH-072===
''Identical to GH-070''<br/>

=PSX Motherboard Models=

===XPD-001===
''Identical to XPD-005''<br/>

===XPD-005===
[[File:Hz1QY2W.jpg|200px]]