Editing PSX

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 343: Line 343:


== Disc Drive ==
== Disc Drive ==
The PS2-part of the drive is based on the H/I chassis SCPH-500xx/5500x fat PS2 drive, both electrically and mechanically. The whole drive assembly is connected to the motherboard using 3 flat flex cables: One is an IDE connection to the dedicated drive board of the PSX-part, one provides power (5V, 12V, GND) and also connects the PS2-part sled motor to the motherboard (since it is controlled by the motherboard directly), and one connects the [[KHS-400C]] PS2-part pickup to the motherboard, since it is also directly controlled by the motherboard. The spindle motor is always controlled by the dedicated PSX-part drive electronics over IDE, even in PS2 mode.
The PS2-part of the drive is based on the H/I chassis SCPH-500xx/5500x fat PS2 drive, both electrically and mechanically. The whole drive assembly is connected to the motherboard using 3 flat flex cables: One is an IDE connection to the dedicated drive board of the PSX-part, one provides power (5V, 12V, GND) and also connects the PS2-part sled motor to the motherboard (since it is controlled by the motherboard directly), and one connects the KHS-400C PS2-part pickup to the motherboard, since it is also directly controlled by the motherboard. The spindle motor is always controlled by the dedicated PSX-part drive electronics over IDE, even in PS2 mode.


Two different models have been made; the older one is used in DESR-x000 and x100, the newer one in DESR-x500 and x700. The drive has an updatable firmware for the PSX-mode part of the drive; at least the newer drive actually received such an update (Sony model name: DW-DX02A, known firmware versions: 0YX7 Sep 15 2004, BV1M Mar 08 2005).
Two different models have been made; the older one is used in DESR-x000 and x100, the newer one in DESR-x500 and x700. The drive has an updatable firmware for the PSX-mode part of the drive; at least the newer drive actually received such an update (Sony model name: DW-DX02A, known firmware versions: 0YX7 Sep 15 2004, BV1M Mar 08 2005).


* DESR-x000 and DESR-x100 drive
* DESR-x000 and DESR-x100 drive
** Uses Sony [[KWS-200A]] optical pickup
** Uses Sony KWS-200A optical pickup
[[File:8UIuNSN.jpg|200px]]
[[File:8UIuNSN.jpg|200px]]


* DESR-x500 and DESR-x700 drive
* DESR-x500 and DESR-x700 drive
** Uses Sanyo [[SF-DB11]] optical pickup
** Uses Sanyo SF-DB11 optical pickup
[[File:XkMxA6G.jpg|200px]]
[[File:XkMxA6G.jpg|200px]]


Line 381: Line 381:
*** ?? (CD front power monitor PDIC)
*** ?? (CD front power monitor PDIC)
*** ?? (CD laser diode; internal power monitoring photo diode is unused; external front power monitoring PDIC does power monitoring instead)
*** ?? (CD laser diode; internal power monitoring photo diode is unused; external front power monitoring PDIC does power monitoring instead)
**** Specs for reading: 790 nm at 1.55 mW to 1.65 mW  (measured on top of the whole pickup, not directly at the LD)
**** Specs for writing: 790 nm at 31.75 mW to 33 mW  (measured on top of the whole pickup, not directly at the LD)
*** ?? (DVD laser diode; internal power monitoring photo diode is unused; external front power monitoring PDIC does power monitoring instead)
*** ?? (DVD laser diode; internal power monitoring photo diode is unused; external front power monitoring PDIC does power monitoring instead)
**** Specs for reading: 660 nm at 0.72 mW to 0.78 mW  (measured on top of the whole pickup, not directly at the LD)
**** Specs for writing: 660 nm at 11 mW to 12 mW  (measured on top of the whole pickup, not directly at the LD)


=== Integrated Circuits (MA-S43, used in DESR-x500 and DESR-x700) ===
=== Integrated Circuits (MA-S43, used in DESR-x500 and DESR-x700) ===
Line 394: Line 390:
** IC603: Mediatek MT1828E (main DVD-drive/burner controller, includes microcontroller/s, DSP, EnDec etc.,  no public datasheet available)
** IC603: Mediatek MT1828E (main DVD-drive/burner controller, includes microcontroller/s, DSP, EnDec etc.,  no public datasheet available)
*** Pinout available from some PC DVD drive's schematics
*** Pinout available from some PC DVD drive's schematics
*** Has an 80C32/MCS-51 8-Bit microcontroller core as other Mediatek chipsets from that time do.
*** Likely has one or more 80C32/MCS-51 8-Bit microcontroller cores as other Mediatek chipsets from that time do.
*** Has a debug header on board; see above for pinout
*** Has a debug header on board; see above for pinout
* ROM and Flash
* ROM and Flash
Line 411: Line 407:
** IC403: ST KF25 (2.5V low drop voltage regulator)
** IC403: ST KF25 (2.5V low drop voltage regulator)
** IC1000: Fairchild FAN8035L (6-CH Motor Driver)
** IC1000: Fairchild FAN8035L (6-CH Motor Driver)
** On the pickup:  
** On the pickup: Elantec/Intersil EL6833CLZ (Laser Diode driver)
*** Elantec/Intersil EL6833CLZ (Laser Diode driver)


=== Notes ===
=== Notes ===
* Contrary to some information on the internet, the drive does NOT seem to be married to the individual console. It is however likely that you can not replace the older drive type by the newer type or vice versa (needs verification, please contribute), due to different specifications and features, despite identical electrical interfaces (which is just IDE/ATA through a 50 pin flat flex cable).
* Contrary to some information on the internet, the drive does NOT seem to be married to the individual console. It is however likely that you can not replace the older drive type by the newer type or vice versa (needs verification, please contribute), due to different specifications and features, despite identical electrical interfaces (which is just IDE/ATA through a 50 pin flat flex cable).
* Several variants of the Sanyo [[SF-DB11]] pickup exist, with only some of them being compatible with the PSX. Trying to install an incompatible one will (sometimes? always?) burn the flat flex cable and/or blow the 5V drive-power fuse on the motherboard depending on your luck (known compatible variants: bottom sticker number starts with DB11B; known incompatible revisions: bottom sticker number starts with DB11N, 11NX or 11NXL). It didn't seem to damage anything else though; most notably all electronics (after replacing the blown fuse) AND the laser pickup (after being installed into a compatible PC drive that uses this variant) survived.  
* Several variants of the Sanyo SF-DB11 pickup exist, with only some of them being compatible with the PSX. Trying to install an incompatible one will (sometimes? always?) burn the flat flex cable and/or blow the 5V drive-power fuse on the motherboard depending on your luck (known compatible variants: bottom sticker number starts with DB11B; known incompatible revisions: bottom sticker number starts with DB11N, 11NX or 11NXL). It didn't seem to damage anything else though; most notably all electronics (after replacing the blown fuse) AND the laser pickup (after being installed into a compatible PC drive that uses this variant) survived.  
** These different types are seemingly actually called "SF-DB11B" (the one compatible with the PSX), "SF-DB11NS", "SF-DB11NX" and "SF-DB11NXL" (all three incompatible with PSX). These are best differentiated by the bottom sticker, not by the embossed revision number on the top.
** These different types are seemingly actually called "SF-DB11B" (the one compatible with the PSX), "SF-DB11NS", "SF-DB11NX" and "SF-DB11NXL" (all three incompatible with PSX). These are best differentiated by the bottom sticker, not by the embossed revision number on the top.
** Symptoms of a blown 5V fuse:  
** Symptoms of a blown 5V fuse:  
Line 423: Line 418:
*** The front USB port does not work
*** The front USB port does not work
** [[File:jPNVCqr.jpg|200px]][[File:Vo2DfEx.jpg|200px]]
** [[File:jPNVCqr.jpg|200px]][[File:Vo2DfEx.jpg|200px]]
** Comparison of an compatible type (left) with an incompatible type (right) of [[SF-DB11]] with the bottom shielding removed. Note the missing potentiometers for setting the oscillator frequencies on the incompatible type, where fixed 680 Ohm resistors are used instead:<br />[[File:UJjmXaf.jpg|200px]]
** Comparison of an compatible type (left) with an incompatible type (right) of SF-DB11 with the bottom shielding removed:<br />[[File:UJjmXaf.jpg|200px]]
* There is an official documentation of the [[KWS-200A]] used in the DESR-x000 and DESR-x100 PSX, released by Sony itself, however, both power monitoring PDICs are absent in the drawing:<br/> [[File:TxkqxiO.jpg|200px]] [[File:tyimnzA.jpg|200px]]
* There is an official documentation of the KWS-200A used in the DESR-x000 and DESR-x100 PSX, released by Sony itself, however, both power monitoring PDICs are absent in the drawing:<br/> [[File:TxkqxiO.jpg|200px]] [[File:tyimnzA.jpg|200px]]


== Motherboards ==
== Motherboards ==
Line 652: Line 647:
| '''Dimension''' || 312 x 323 x 88mm(W x H x D)
| '''Dimension''' || 312 x 323 x 88mm(W x H x D)
|-
|-
| '''Weight''' || ~5.5kg for first gen models. ~6.5kg for second gen models
| '''Weight''' || Approximately 5.8kg
|-
|-
| '''Accessories''' ||  
| '''Accessories''' ||  
Please note that all contributions to PS2 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS2 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)

Templates used on this page: