Editing MechaCon/UART commands/SPC970

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 2: Line 2:
See [[MechaCon]] and [[MechaCon/UART commands]] for basic information.
See [[MechaCon]] and [[MechaCon/UART commands]] for basic information.
= Command list =
= Command list =
'''Note: This is subject to ongoing research and partially inaccurate'''<br/>
'''Note: This is subject to ongoing research and partially inaccurate'''
'''All communication uses ASCII-encoded Hex-values.'''


''Not all of these commands are available on every MechaCon version''
''Not all of these commands are available on every MechaCon version''
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"
|- bgcolor="#cccccc"
|- bgcolor="#cccccc"
! Command !! Description !! Parameters !! Return values !! Usage/Remarks
! Command !! Description !! Parameters !! Return values !! Remarks
|-
|-
| 0xc00 || MECHA_CMD_INIT_SHIMUKE || || ||
| 0xc00 || MECHA_CMD_INIT_SHIMUKE || || ||
Line 72: Line 71:
| 0xc9a || MECHA_CMD_READ_CHECKSUM ||  ||  ||
| 0xc9a || MECHA_CMD_READ_CHECKSUM ||  ||  ||
|-
|-
| 0xc9b || MECHA_CMD_SETUP_OSD ||  ||  || 00 = NTSC, 01 = PAL, presumed to be supported by DEX B and later
| 0xc9b || MECHA_CMD_SETUP_OSD ||  ||  || 00 = NTSC, 01 = PAL, presumed to be supported by DEX B and later.
|-
|-
| 0xc9e || MECHA_CMD_SETUP_SANYO ||  ||  ||
| 0xc9e || MECHA_CMD_SETUP_SANYO ||  ||  ||
Line 82: Line 81:
| 0xca3 || MECHA_CMD_AUTO_ADJ_ST_12 ||  ||  ||
| 0xca3 || MECHA_CMD_AUTO_ADJ_ST_12 ||  ||  ||
|-
|-
| 0xca4 || MECHA_CMD_AUTO_ADJ_ST_2MD ||  ||  || Performed during skew adjustment initialization
| 0xca4 || MECHA_CMD_AUTO_ADJ_ST_2MD ||  ||  || Performed during skew adjustment initialization.
|-
|-
| 0xca5 || MECHA_CMD_AUTO_ADJ_FIX_GAIN ||  ||  ||
| 0xca5 || MECHA_CMD_AUTO_ADJ_FIX_GAIN ||  ||  ||
Line 142: Line 141:
| 0xcdf || MECHA_CMD_DSP_ERROR_RATE ||  ||  ||
| 0xcdf || MECHA_CMD_DSP_ERROR_RATE ||  ||  ||
|-
|-
| 0xce0 || MECHA_CMD_EEPROM_WRITE || aaaadddd || 0aaaadddd (returns written data, not previous data)|| ce0aaaadddd    (a = address, d = data)
| 0xce0 || MECHA_CMD_EEPROM_WRITE || aaaadddd || || ce0aaaadddd    a = address, d = data.
|-
|-
| 0xce1 || MECHA_CMD_EEPROM_READ || aaaa || 0aaaadddd || ce1aaaa    (a = address)
| 0xce1 || MECHA_CMD_EEPROM_READ || aaaa || || ce1aaaa    a = address
|-
|-
| 0xce4 || MECHA_CMD_RTC_READ ||  ||  ||
| 0xce4 || MECHA_CMD_RTC_READ ||  ||  ||
Line 159: Line 158:
|-
|-
| 0xcf2 || MECHA_CMD_FOCUS_JUMP_NEW ||  ||  ||
| 0xcf2 || MECHA_CMD_FOCUS_JUMP_NEW ||  ||  ||
|-
| 0xcf4 || MECHA_CMD_WRITE_1A6 ||  ||  ||
|-
| 0xcf5 || MECHA_CMD_READ_1A6 ||  ||  ||
|-
| 0xcf6 || MECHA_CMD_READ_1EA_1FA ||  ||  ||
|-
| 0xcf7 || MECHA_CMD_WRITE_1EA_1FA ||  ||  ||
|-
| 0xcfa || MECHA_CMD_WRITECONFIG ||  ||  ||
|-
| 0xcfb || MECHA_CMD_READCONFIG ||  ||  ||
|-
|-
| 0xcfc || MECHA_CMD_READ_MODEL_2 ||  ||  ||
| 0xcfc || MECHA_CMD_READ_MODEL_2 ||  ||  ||
|-
|-
| 0xcfd || MECHA_CMD_READ_MODEL ||  || vvvvrr (v = [[MechaCon#Firmware_revisions|version]], r = [[MechaCon#Bits|region]]) ||
| 0xcfd || MECHA_CMD_READ_MODEL ||  || ||
|-
|-
| 0xcfe || MECHA_CMD_EEPROM_ERASE ||  ||  ||
| 0xcfe || MECHA_CMD_EEPROM_ERASE ||  ||  ||
Line 171: Line 182:
= Command documentation =
= Command documentation =
''To do: document more complex commands here''
''To do: document more complex commands here''
= Error codes =
{| border="1" cellspacing="0" cellpadding="5" border="#999" class="wikitable" style="border:1px solid #999; border-collapse: collapse;"
|- bgcolor="#cccccc"
! Code !! Description
|-
| 0x2A0 || Rx-command error
|-
| 0x2A1 || Rx-command invalid argument count error
|-
| 0x2A2 || Rx-command invalid argument error
|-
|}
Please note that all contributions to PS2 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS2 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)
Retrieved from "http://www.psdevwiki.com/ps2/MechaCon/UART_commands/SPC970"