Editing DSP

Jump to navigation Jump to search
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then publish the changes below to finish undoing the edit.

Latest revision Your text
Line 1: Line 1:
Used for signal processing as part of the CD/DVD drive. Not to be confused with [[MechaCon]] in this matter, which is responsible for the drive mechanics among many other functions.
Used for signal processing as part of the CD/DVD drive. Not to be confused with [[MechaCon]] in this matter, which controls and adjusts the drive mechanics and the laser among other functions.


DSP firmware resides in a mask-ROM inside the DSP. Several firmware versions might exist for the same DSP hardware revision.
DSP firmware resides in a mask-ROM inside the DSP. Several firmware versions might exist for the same DSP hardware revision.


At least one version of the DSP's firmware (specifically the CXD3098Q) has a tendency to crash MechaCon by sheer bad luck or on badly readable discs (e.g. badly burned/low-quality DVD-R discs or scratched original discs), overvolting the focus/tracking coils of the laser and killing them and also the driver IC in the process. Several hardware-based mitigations/"fixes" have been developed by the community to address this issue with varying degrees of success. The most well known of these fixes have been the "Romeo-mod"/"LA-fix" for SCPH-500xx/5500x consoles and "summ0ne's fix" for some SCPH-700xx consoles; however, the only reliable fix is the Matrix team's PIC-fix which monitors communication between DSP and MechaCon and turns off the console when a crash occurs, just like the hotfix made by Sony itself.
Some versions of the DSP's firmware (specifically in SCPH-5XXXX and SCPH-70XXX consoles) have a tendency to crash MechaCon by sheer bad luck or on badly readable discs (e.g. badly burned/low-quality DVD-R discs or scratched originals), overvolting the focus/tracking coils of the laser and killing them and also the driver IC in the process. Several hardware-based mitigations/"fixes" have been developed by the community to address this issue with varying degrees of success. The most well known of these fixes have been the "Romeo-mod"/"LA-fix" for SCPH-5XXXX consoles and "summ0ne's fix" for SCPH-70XXX consoles; however, the most reliable fix is the Matrix PIC fix which monitors communication between DSP and MechaCon and turns off the console when a crash occurs.
 
The CXD3098Q DSP chips of DEX models (DTL-H5000x & DTL-H700xx) are not capable of producing the crash. This was fixed by Sony on the software. A dump of the DSP firmware on these units revealed that the only difference between retail and DEX firmware is a -1 (signed byte) at the end of the firmware.  


== Revisions ==
== Revisions ==
*CXD1869Q (GH-001, GH-003)
*CXD1869Q (GH-001, GH-003)
*CXD1869Q-1 (DIF-2, DTL-T10000 DVD interface board)
** ''GH-008?''
*CXD1869AQ (GH-004, GH-005, GH-006, GH-007, GH-008, GH-010, GH-012, GH-013, GH-014)
*CXD1869AQ (GH-004, GH-005, GH-006, GH-007, GH-010, GH-012, GH-013, GH-014)
*CXD1869BQ (GH-010, GH-012, GH-013, GH-014)
*CXD1869BQ (GH-010, GH-012, GH-013, GH-014)
*CXD1869BQ-1 (DIF-001, DTL-T15000 DVD interface board)
*CXD1886Q (GH-013, GH-014, GH-015)
*CXD1886Q (GH-013, GH-014, GH-015, GH-016)
** ''GH-016?''
** Die size: about 8 x 8 mm
*CXD3098Q (GH-017, GH-019, GH-022, GH-023, GH-026, GH-027, GH-029, GH-032, GH-035, GH-036, GH-037, GH-040, GH-041, GH-051, GH-052, XPD-001, XPD-005)
** Die marking: D1886 (M)(C)SONY'01
** Units used on GH-023 to GH-035 have a bug in their firmware which causes MechaCon to freeze when bad sectors are read (e.g. on burnt or scratched discs)
*CXD3098Q (GH-017, GH-018, GH-019, GH-022, GH-023, GH-026, GH-027, GH-029, GH-032, GH-035, GH-036, GH-037, GH-040, GH-041, GH-051, GH-052, GH-061, XPD-001, XPD-005)
*CXD3098AQ (GH-061, GH-062, GH-070, GH-071, GH-072)
** Has a (very likely) intentional bug in the firmware which causes MechaCon to freeze/crash when bad ECC sectors are read (e.g. badly burned/low quality DVD-R discs or scratched original discs). This likelyhood is increased on ARM-based Dragon [[MechaCon]], thus SCPH-500xx/5500x units up to some (mostly earlier) SCPH-700xx units. Some later subrevisions of the GH-032/GH-035 boards implement a factory safety circuit to prevent this from happening, they can be identified via the Mechacon version: if it's 6.04 or newer, the console has the factory safety circuit.
*CXD3098Q-1 (DTL-H5000x, DTL-H700xx, DTL-H75000)
*CXD3098AQ (GH-052, GH-061, GH-062, GH-070, GH-071, GH-072)
Please note that all contributions to PS2 Developer wiki are considered to be released under the GNU Free Documentation License 1.2 (see PS2 Developer wiki:Copyrights for details). If you do not want your writing to be edited mercilessly and redistributed at will, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource. Do not submit copyrighted work without permission!

To protect the wiki against automated edit spam, we kindly ask you to solve the following hCaptcha:

Cancel Editing help (opens in new window)